Limited Internal
E
EBAOCMA
PRODUCT SPECIFICATION
2 (5)
Prepared (also subject responsible if other)
No.
2/1301-BMR 637 02/3 Uen
11
Technical Specification
Approved
Checked
Date
Rev
EN/LZT 146 3R0e6feRre4nAceJuly 2008
PKM 4000D PINB Series
MPM/BM/Y (Maria Rosendahl)
MICOSPE
2006-10-17
C
© Ericsson Power Modules AB
DC/DC converters, Input 36-75 V, Output 40 A/132 W
5.0 V Electrical Specification
PKM 4111D PINB
Tref = -40 to +90ºC, VI = 36 to 75 V, unless otherwise specified under Conditions.
Typical values given at: Tref = +25°C, VI= 53 V, max IO , unless otherwise specified under Conditions.
Characteristics
Conditions
min
36
typ
max
75
Unit
V
VI
Input voltage range
VIoff
VIon
CI
Turn-off input voltage
Turn-on input voltage
Internal input capacitance
Output power
Decreasing input voltage
Increasing input voltage
32
34
V
V
4.3
µF
W
PO
Output voltage initial setting
f = 100 Hz sinewave, 1 Vp-p
50 % of max IO
0
125
SVR
Supply voltage rejection (ac)
60
92
91
92
91
dB
max IO
89
η
Efficiency
%
50 % of max IO , VI = 48 V
max IO , VI = 48 V
max IO
Pd
Pli
Power Dissipation
Input idling power
Input standby power
Switching frequency
15.5
W
W
IO= 0, VI = 53 V
3.1
100
200
PRC
fs
VI = 53 V (turned off with RC)
0 -100% of max IO
mW
kHz
180
220
Output voltage initial setting and
accuracy
4.90
5.00
5.10
V
T
ref = +25°C, VI = 53 V, IO = 40.0 A
VOi
Vadj, see Note 1
Output adjust range
Output voltage tolerance band
Idling voltage
4.50
4.80
4.80
5.50
5.20
5.20
15
V
V
10-100% of max IO
IO = 0
V
VO
Line regulation
max IO
mV
mV
Load regulation
VI = 53 V, 1-100% of max IO
15
Load transient
voltage deviation
VI = 53 V, Load step 25-75-25 % of
max IO, di/dt = 1 A/µs,
see Note 2
Vtr
ttr
tr
±500
100
13
mV
Us
Load transient recovery time
Ramp-up time
(from 10−90 % of VOi)
6
30
ms
10-100% of max IO
Start-up time
(from VI connection to 90% of VOi)
ts
9
0
15
50
25
ms
IO
Output current
A
A
A
Ilim
Isc
Current limit threshold
Short circuit current
Vo = 4.5 V, Tref < max Tref
30
40
Tref = 25ºC, VO = < VOnom * 0.1
See ripple & noise section,
max IO, VO.
VOac
Output ripple & noise
60
150
mVp-p
V
Tref = +25°C, VI = 53 V, IO = 0-100%
OVP
Over Voltage Protection
6.2
of max IO
Note 1: When using Vadj function, max output power (PO) must not be exceeded
Note 2: Output filter according to Ripple & Noise section
ERICSSON [ ERICSSON ]
