General
Absolute Maximum Ratings
Characteristics
T
C
T
S
V
I
V
ISO
W
tr
V
RC
V
adj
Case temperature at full output power
Storage temperature
Continuous input voltage
1)
Isolation voltage
(input to output test voltage)
Transient input energy
Remote control voltage pin 10,11
Output adjust voltage pin 8, 9
–5
–5
min
–45
–55
–0.5
1,500
0.01
+16
+ 40
max
+100
+125
+75
Unit
°C
°C
V dc
V dc
Ws
V dc
V dc
Stress in excess of Absolute Maximum Rat-
ings may cause permanent damage. Absolute
Maximum Ratings, sometimes referred to as
no destruction limits, are normally tested
with one parameter at a time exceeding the
limits of Output data or Electrical Charac-
teristics. If exposed to stress above these
limits, function and performance may de-
grade in an unspecified manner.
NOTES:
Input
T
C
< T
Cmax
unless otherwise specified
Characteristics
V
I
V
Ioff
V
Ion
C
I
P
Ii
P
RC
Input voltage range
1)
Turn-off input voltage
Turn-on input voltage
Input capacitance
Input idling power
I
O
= 0, T
C
= – 30…+ 90 °C
(V
I
= 27V)
(V
I
= 53 V)
(See typical characteristics)
(See typical characteristics)
1)
Conditions
min
18
15
typ
max
72
Unit
V
V
16
17.4
1.4
244
240
18
67
17.9
V
mF
2)
The input voltage range 18…72 V dc meets
the European Telecom Standard
ETS 300 132-2 Nominal input voltage range
in 48 V and 60 V dc power systems, – 40.5…
–57.0 V and –50.0… – 72.0 V respectively. At
input voltages exceeding 72 V (abnormal
voltage) the power loss will be higher than at
normal input voltage and T
C
must be limited to
max +90 °C. Absolute max continuous input
voltage is 75 V dc. Output characteristics will
be marginally affected at input voltages
exceeding 72 V.
The test is applicable for through-hole
versions.
mW
Input stand-by power
(V
I
= 27V)
T
C
= – 30…+ 90 °C
RC connected to pin 17 (V
I
= 53 V)
mW
Environmental Characteristics
Characteristics
Vibration
(Sinusoidal)
JESD 22-B103
(IEC 68-2-6 F
c
)
Test procedure & conditions
Frequency
Amplitude
Acceleration
Number of cycles
Frequency
Acceleration density
spectrum
Duration
Reproducability
Peak acceleration
Shock duration
Temperature
Number of cycles
Temperature
Humidity
Duration
Temperature, solder
Duration
Duration
Temperature
Concentration
10…500 Hz
0.75 mm
10 g
10 in each axis
10…500 Hz
0.5 g
2
/Hz
10 min in 3 directions
medium (IEC 62-2-36)
200 g
3 ms
–40°C…+125°C
500
85°C
85% RH
1000 hours
260°C
10…13 s
96 h
35°C
5%
Random
vibration
MIL-STD-883
Method 2026
(IEC 68-2-34 E
d
)
Shock
(Half sinus)
Temperature
change
Accelerated
damp heat
Solder
resistability
2)
Aggressive
environment
JESD 22-B104
(IEC 68-2-27 E
a
)
JESD 22-A104
(IEC 68-2-14 N
a
)
JESD 22-A101
(IEC 68-2-3 C
a
with bias)
JESD 22-B106
(IEC 68-2-20 T
b
1A)
IEC 68-2-11 K
a
2
EN/LZT 146 32 R1A (Replaces EN/LZT 137 27 R3) © Ericsson Microelectronics, June 2000
ERICSSON [ ERICSSON ]
