General
Absolute Maximum Ratings
min
Characteristics
Unit
°C
max
+100
+125
Stress in excess of Absolute Maximum Rat-
ings may cause permanent damage. Absolute
Maximum Ratings, sometimes referred to as
no destruction limits, are normally tested
with one parameter at a time exceeding the
limits of Output data or Electrical Charac-
teristics. If exposed to stress above these
limits, function and performance may de-
grade in an unspecified manner.
Case temperature at full output power
Storage temperature
–45
–55
TC
TS
°C
Continuous input voltage1)
–0.5
+75
Vdc
Vdc
VI
Isolation voltage
(input to output test voltage)
VISO
1,500
Ws
Vdc
Vdc
0.01
+16
+40
Wtr
Transient input energy
Remote control voltage pin 10,11
Output adjust voltage pin 8, 9
VRC
Vadj
–5
–5
NOTES:
1)
The input voltage range 18…72 Vdc meets
Input TC < TCmax unless otherwise specified
the European Telecom Standard
ETS 300 132-2 Nominal input voltage range
in 48 V and 60 Vdc power systems, –40.5…
–57.0V and –50.0…–72.0V respectively. At
input voltages exceeding 72 V (abnormal
voltage) the power loss will be higher than at
normal input voltage and TC must be limited to
max +90°C. Absolute max continuous input
voltage is 75 Vdc. Output characteristics will
be marginally affected at input voltages
exceeding 72 V.
Characteristics
max
Unit
Conditions
typ
min
18
Input voltage range1)
VI
72
V
V
Turn-off input voltage
Turn-on input voltage
Input capacitance
VIoff
VIon
CI
(See typical characteristics)
(See typical characteristics)
15
16
17.4
1.4
V
17.9
mF
2)
The test is applicable for through-hole
versions.
(VI = 27V)
(VI = 53V)
244
240
IO=0,TC= –30…+90°C
TC= –30…+90°C
Input idling power
mW
mW
PIi
(VI = 27V)
RC connected to pin 17 (VI = 53V)
18
67
PRC
Input stand-by power
Environmental Characteristics
Characteristics
Test procedure & conditions
Frequency
Amplitude
10…500 Hz
0.75 mm
Vibration
(Sinusoidal)
JESD 22-B103
(IEC 68-2-6 Fc)
Acceleration
Number of cycles
10 g
10 in each axis
Frequency
Acceleration density
spectrum
10…500 Hz
0.5 g2/Hz
MIL-STD-883
Method 2026
(IEC 68-2-34 Ed)
Random
vibration
Duration
Reproducability
10 min in 3 directions
medium (IEC 62-2-36)
Shock
(Half sinus)
Peak acceleration
Shock duration
200 g
3 ms
JESD 22-B104
(IEC 68-2-27 Ea)
Temperature
change
JESD 22-A104
(IEC 68-2-14 Na)
Temperature
Number of cycles
–40°C…+125°C
500
JESD 22-A101
(IEC 68-2-3 Ca
with bias)
Temperature
Humidity
Duration
85°C
85% RH
1000 hours
Accelerated
damp heat
Solder
resistability2)
JESD 22-B106
(IEC 68-2-20 Tb 1A)
Temperature, solder
Duration
260°C
10…13 s
Duration
Temperature
Concentration
96 h
35°C
5 %
Aggressive
environment
IEC 68-2-11 Ka
2
EN/LZT 146 32 R1A (Replaces EN/LZT 137 27 R3) ©Ericsson Microelectronics, June 2000
ERICSSON [ ERICSSON ]
