欢迎访问ic37.com |
会员登录 免费注册
发布采购

PKB4713PILA 参数 Datasheet PDF下载

PKB4713PILA图片预览
型号: PKB4713PILA
PDF下载: 下载PDF文件 查看货源
内容描述: [DC-DC Regulated Power Supply Module, 1 Output, 72W, Hybrid, 2.280 X 0.785 INCH, LOW PROFILE PACKAGE-8]
分类和应用:
文件页数/大小: 8 页 / 709 K
品牌: ERICSSON [ ERICSSON ]
 浏览型号PKB4713PILA的Datasheet PDF文件第1页浏览型号PKB4713PILA的Datasheet PDF文件第3页浏览型号PKB4713PILA的Datasheet PDF文件第4页浏览型号PKB4713PILA的Datasheet PDF文件第5页浏览型号PKB4713PILA的Datasheet PDF文件第6页浏览型号PKB4713PILA的Datasheet PDF文件第7页浏览型号PKB4713PILA的Datasheet PDF文件第8页  
PKB 4713 PINB  
General  
Safety  
Absolute Maximum Ratings  
The PKB 4000 PI Series DC/DC converters  
are designed in accordance with Safety  
Standards IEC/EN/UL 60 950, Safety of  
Information Technology Equipment.  
Characteristics  
min  
max  
Unit  
TPcb  
TS  
Maximum Operating Pcb Temperature  
Storage temperature  
40  
55  
+110  
+125  
°C  
°C  
The PKB 4000 Series DC/DC converters are  
ULC 60 950 recognized and certified in  
accordance with EN 60 950.  
VI  
Input voltage  
0.5  
+80  
Vdc  
Vdc  
VISO  
2250  
Isolation voltage (input to output test voltage)  
VTrans  
VRC  
Input Voltage Transient  
(10 usec)  
100  
Vdc  
The DC/DC converters should be installed in  
end-use equipment, in accordance with the  
requirements of the ultimate application.  
The input source must be isolated by  
minimum Basic Insulation from the primary  
circuit in accordance with IEC/EN/UL 60  
950. If the input voltage to the DC/DC  
converter is 75Vdc or less, then the output  
remains SELV (Safety Extra Low Voltage)  
under normal and abnormal operating  
conditions. Single fault testing in the input  
power source circuit should be performed  
with the DC/DC converter connected to  
demonstrate that the input voltage does not  
exceed 75Vdc. If the input power source  
circuit is a DC power system, the source  
maybe treated as a TNV2 circuit and testing  
has demonstrated compliance with SELV  
limits and isolation requirements equivalent  
to Basic Insulation in accordance with IEC/  
EN/UL 60 950.  
-0.5  
-0.5  
15  
Vdc  
Vdc  
Remote control voltage pin 2 (measured from pin 1)  
Output adjust voltage pin 6 (measured from pin 5)  
Vadj  
2 x Vo  
Note:  
Stress in excess of Absolute Maximum Ratings may cause permanent damage. Absolute Maximum Ratings,  
sometimes referred to as "no destruction limits", are normally tested with one parameter at a time  
exceeding the limits of the Output data or Electrical Characteristics.  
Input TPcb < TPcb max  
Characteristics  
Conditions  
min  
typ  
max  
Unit  
VI  
VI  
Input voltage range1)  
IO = 0...IOmax  
38  
30  
75  
35  
Vdc  
Vdc  
Turn-off input voltage  
Turn-on input voltage  
Ramping from higher  
voltage  
33.5  
34.5  
off  
VIon  
Ramping from lower  
voltage, IO = 0...IOmax  
32  
36  
Vdc  
C I  
IIac  
Input capacitance  
2.18  
10  
uF  
Reflected ripple current  
5 Hz to 20 MHz  
mAp-p  
II  
Maximum input current  
Input idling power  
VI = VImin,  
IO =0, V = 53 V  
72 W  
2.38  
1.6  
A
max  
PIi  
W
W
I
PRC  
Input stand-by power  
(turned off with RC)  
V =53V, RC open  
0.055  
I
It is recommended that a fast blow fuse with a  
rating of 5A be used at the input of each DC/  
DC converter. The PKB series DC/DC  
converters are approved for a maximum fuse  
rating of 15A. If a fault occurs in the DC/DC  
converter that imposes a short circuit on the  
input power source, this fuse will provide the  
following functions:  
VTRIM  
Maximum input voltage  
on trim pin  
6.6  
Vdc  
Note:  
1) The input voltage range 38...75 V meets the requirements in the European Telecom Standard prETS 300  
132-2 for Normal input voltage range in 48 V and 60 V DC power systems, 40.5...–57.0 V and –50.0...–72.0 V  
respectively.  
Environmental Characteristics  
Characteristics  
Test procedure & conditions  
Random  
Vibration  
IEC 68-2-34ED  
IEC 68-2-6 Fc  
Frequency  
Spectral density  
Duration  
10...500 Hz  
Isolate the faulty DC/DC converter from the  
input source so as not to affect the  
2
0.025 g /Hz  
10 min each direction  
operation of other parts of the system.  
Sinusoidal  
Vibration  
Frequency  
Amplitude  
10...500 Hz  
0.75mm  
• Protect the distribution wiring from  
excessive current and power loss thus  
preventing hazardous overheating.  
Acceleration  
Number of cycles  
10g  
10 in each axis  
Shock  
(Half sinus)  
IEC 68-2-27 Ea  
IEC 68-2-14 Na  
Peak acceleration  
Duration  
100g  
3ms  
Temperature  
Number of cycles  
-40°C… +125°C  
300  
Temperature  
change  
The galvanic isolation is verified in an electric  
strength test. The test voltage (VISO) between  
input and output is 2250 Vdc for 60 seconds.  
Leakage current is less than 1uA at nominal  
input voltage.  
Temperature  
Humidity  
Duration  
85°C  
85% RH  
1000 hours  
Accelerated  
damp heat  
IEC 68-2-3 Ca  
with bias  
Temperature, solder 260°C  
Duration  
Solder  
resistability  
IEC 68-2-20 Tb 1A  
10…13 s  
Water  
Isopropyl alcohol  
Method  
+55 ±5°C  
+35 ±5°C  
with rubbing  
Resistance to  
cleaning solvents  
IEC 68-2-45 XA  
Method 1  
The flammability rating for all construction  
parts of the DC/DC converter meets UL 94V-0.  
EN/LZT 108 6071 P1D ©Ericsson Inc., Power Modules , February 2003  
2