欢迎访问ic37.com |
会员登录 免费注册
发布采购

EPC110 参数 Datasheet PDF下载

EPC110图片预览
型号: EPC110
PDF下载: 下载PDF文件 查看货源
内容描述: 完全集成的可配置的光障的驱动程序和接收器 [Fully integrated configurable light barrier driver & receiver]
分类和应用: 驱动
文件页数/大小: 27 页 / 588 K
品牌: EPC [ ESPROS PHOTONICS CORP ]
 浏览型号EPC110的Datasheet PDF文件第10页浏览型号EPC110的Datasheet PDF文件第11页浏览型号EPC110的Datasheet PDF文件第12页浏览型号EPC110的Datasheet PDF文件第13页浏览型号EPC110的Datasheet PDF文件第15页浏览型号EPC110的Datasheet PDF文件第16页浏览型号EPC110的Datasheet PDF文件第17页浏览型号EPC110的Datasheet PDF文件第18页  
epc110  
DEC  
1
17  
12...9 Weight of missing pulse counts. Refer to Pulse Modulated Operation (e.g. OUTNint to OUTN):  
Minimum number of missing pulses nM of light detection for counting the release time (fall time) tF.  
12 11 10  
9
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
DEC Min. nM  
Setting  
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
1
32768  
X (Default setting)  
16384  
8192  
4096  
2048  
1024  
512  
256  
128  
64  
2
3
4
5
6
7
8
9
10  
11  
12  
13  
14  
15  
32  
16  
8
X (typical setting)  
4
2
1
TPER  
1
17  
15...13 For fork light barrier, standalone mode: LED cycle time tCycle  
.
For fork light barrier, controlled mode: Select next lower value then external EN cycle time.  
15 14 13  
Values Default  
Recommended Setting  
0
0
0
0
1
1
1
1
0
0
1
1
0
0
1
1
0
1
0
1
0
1
0
1
5μs  
10μs  
X
30μs  
100μs  
300μs  
1ms  
X (typical setting)  
10ms  
100ms  
Parameter  
Name  
Register No.  
ROM RAM  
Bit No. Function  
FUSEBIT  
2
18  
0
During write operation to this RAM register, put this bit = 0.  
This bit will be set automatically, when corresponding ROM register is programmed.  
0
0
1
Values  
The corresponding ROM register is not programmed  
The corresponding ROM register is programmed  
SENSN  
2
18  
3...1  
Lower threshold setting of the photo current sensitivity IPDN to trigger output OUTN.  
3
0
0
0
0
1
1
1
1
2
0
0
1
1
0
0
1
1
1
0
1
0
1
0
1
0
1
Values Default Recommended Comments  
24nA  
36nA  
48nA  
60nA  
72nA  
84nA  
96nA  
108nA  
X
A lower value increases the sensitivity. A too sensitive setting leads to  
false readings because of shot noise of the receiver photo diode and the  
internal amplifier (typ. input noise level is 7nA RMS without photo diode).  
Also induced EMI can lead to false readings if the sensitivity is set too  
low. The EMI sensitivity is heavily depending on the system architecture  
and the electromechanical design. The better the shielding of the chip  
and the photo diode and the better the PCB layout, the better the EMI  
immunity.  
X
The tolerance of the threshold is approx. ±25%.  
© 2011 ESPROS Photonics Corporation  
Characteristics subject to change without notice  
14  
Datasheet epc110 - V2.1  
www.espros.ch