欢迎访问ic37.com |
会员登录 免费注册
发布采购

EM47DM1688SBC 参数 Datasheet PDF下载

EM47DM1688SBC图片预览
型号: EM47DM1688SBC
PDF下载: 下载PDF文件 查看货源
内容描述: JEDEC标准VDD / VDDQ [JEDEC Standard VDD/VDDQ]
分类和应用:
文件页数/大小: 38 页 / 881 K
品牌: EOREX [ EOREX CORPORATION ]
 浏览型号EM47DM1688SBC的Datasheet PDF文件第2页浏览型号EM47DM1688SBC的Datasheet PDF文件第3页浏览型号EM47DM1688SBC的Datasheet PDF文件第4页浏览型号EM47DM1688SBC的Datasheet PDF文件第5页浏览型号EM47DM1688SBC的Datasheet PDF文件第7页浏览型号EM47DM1688SBC的Datasheet PDF文件第8页浏览型号EM47DM1688SBC的Datasheet PDF文件第9页浏览型号EM47DM1688SBC的Datasheet PDF文件第10页  
EM47DM1688SBC
Pin Description (Continued)
DQSU,
C7,B7,F3,G3
/DQSU ,
DQSL,
/DQSL
(Data Strobe)
Output with read data, input with write data. Edge-aligned with read data,
centered in write data. DQSL corresponds to the data on DQL0-DQL7;
DQSU corresponds to the data on DQU0-DQU7. The data strobes DQSL,
and DQSU are paired with differential signals /DQSU and /DQSL
respectively, to provide differential pair signaling to the system during
reads and writes. DDR3 SDRAM supports differential data strobe only and
does not support single-ended.
(Command Inputs)
/RAS ,
/CAS
& /
WE
(along with
/CS
) define the command being entered.
(Input Data Mask)
J3, K3, L3
/RAS ,
/CAS ,
/WE
D3,E7
DMU,DML
DMU & DML are input mask signal for write data. Input data is masked
when DMU or DML are sampled HIGH coincident with that input data
during a write access. DMU & DML is sampled on both edges of DQSU &
DQML respectively.
(Data Input/Output)
D7,C3,C8,C2,A7,
A2,B8,A3
E3,F7,F2,F8,H3,
H8,G2,H7
B2,D9,G7,K2,K9,N
1,N9,R1,R9/A9,B3,
E1,G8,J2,J8,M1,M
9,P1,P9,T1,T9
A1,A8,C1,C9,D2,E
9,F1,H2,H9 /B1,
B9,D1,D8,E2,E8,
F9,G1,G9
L8
DQU0~7
DQL0~7
Data inputs and outputs are on the same pin.
(Data Input/Output)
Data inputs and outputs are on the same pin.
(Power Supply/Ground)
VDD,VSS
VDD and VSS are power supply for internal circuits.
(DQ Power Supply/DQ Ground)
VDDQ
,VSSQ
ZQ
VDDQ and VSSQ are power supply for the output buffers.
(ZQ Calibration)
Reference pin for ZQ calibration
(Active Low Asynchronous Reset)
Reset is active when /RESET is LOW, and inactive when /RESET is
T2
/RESET
HIGH. /RESET must be HIGH during normal operation. /RESET is a
CMOS rail to rail signal with DC high and low at 80% and 20% of VDD, i.e.
1.20V for DC high and 0.30V for DC low.
(Reference Voltage)
H1
M8
J1,J9,L1,L9,
M7,T7
VREFDQ
VREFCA
NC
Reference voltage for DQ
(Reference Voltage)
Reference voltage for CA
(No Connection)
No internal electrical connection is present.
Note: Input pins only BA0-BA2, A0-A13, /RAS , /CAS , /WE , /CS , CKE, ODT and /RESET do not supply
termination.
Jan. 2013
6/38
www.eorex.com