EM6352
Absolute Maximum Ratings
Handling Procedures
Parameter
Symbol
Conditions
This device has built-in protection against high static
voltages or electric fields; however, anti-static precautions
must be taken as for any other CMOS component. Unless
otherwise specified, proper operation can only occur when
all terminal voltages are kept within the voltage range.
Unused inputs must always be tied to a defined logic
voltage level.
Voltage at VDD to GND
Minimum voltage at any
signal pin
Maximum voltage at any
signal pin
Electrostatic discharge
max. to MIL-STD-883C
method 3015.7 with ref. to
VSS
Max. soldering conditions
Storage Temperature
Range
VDD
-0.3V to +6V
VMIN
GND - 0.3V
VDD + 0.3V
VMAX
VESD
2000V
Operating Conditions
Parameter
Symbol Min Max Unit
TMAX
TSTG
250°C x 10s
Supply voltage (note 1)
Operating Temperature
VDD
TA
0.8 5.5
-40 +125 °C
V
-65°C to +150°C
Stresses above these listed maximum ratings may cause
permanent damages to the device. Exposure beyond
specified operating conditions may affect device reliability
or cause malfunction.
Electrical Characteristics
Unless otherwise specified: VDD= 0.8V to 5.5V, TA=+25°C (note 1).
Parameter
Symbol
Conditions
Min
-
Typ
Max
4.5
Unit
+25°C
VDD=1.5V
VDD=3.3V
2.1
-40°C to +125°C
+25°C
-
7
-
5.4
Supply current (note 2)
IDD
2.7
3.2
µ
A
-40°C to +125°C
+25°C
-
8.3
-
6.3
V
DD=5.0V
-40°C to +125°C
-
9.6
EM6352 – 1.3
1.290
1.359
1.546
1.635
1.773
2.167
2.226
2.591
2.886
3.034
4.334
4.561
1.31
1.38
1.57
1.66
1.80
2.20
2.26
2.63
2.93
3.08
4.40
4.63
1.330
1.401
1.594
1.685
1.827
2.233
2.294
2.669
2.974
3.126
4.466
4.699
EM6352 – 1.4
EM6352 – 1.6
EM6352 – 1.7
EM6352 – 1.8
EM6352 – 2.2
EM6352 – 2.26
EM6352 – 2.6
EM6352 – 2.9
EM6352 – 3.1
EM6352 – 4.4
EM6352 – 4.6
Threshold voltage
(note 3)
VTH
V
Threshold voltage
temperature coefficient
(note 4)
∆VTH
∆TA
TA = -40°C to +125°C
-
-
-
-
ppm/°C
V
±
50
Threshold hysteresis
VHYS
2.1% VTH
•
Note 1: Production tested at +25°C only. Over temperature limits are guaranteed by design, not production tested.
VDD min=0.9V for active-high versions (EM6352Z).
Note 2: RESET (RESET) open.
Note 3: Threshold voltage is specified for VDD falling.
Note 4: Typical variation ∆VTH of VTH at a given temperature TA is calculated as follows:
∆VTH
∆TA
∆VTH(T = TA ) =
× VTH × TA − 25°C
Example:
for version VTH=2.93V, variation at TA=70°C is equal to ∆VTH(70°C)=±50
10-6 x 2.93 x (70-25)=±6.59mV
•
3
www.emmicroelectronic.com
Copyright
03/06 – rev.I
© 2006, EM Microelectronic-Marin SA
EMMICRO [ EM MICROELECTRONIC - MARIN SA ]
