欢迎访问ic37.com |
会员登录 免费注册
发布采购

EBJ21EE8BAFA-8C-E 参数 Datasheet PDF下载

EBJ21EE8BAFA-8C-E图片预览
型号: EBJ21EE8BAFA-8C-E
PDF下载: 下载PDF文件 查看货源
内容描述: 2GB DDR3无缓冲SDRAM DIMM [2GB Unbuffered DDR3 SDRAM DIMM]
分类和应用: 存储内存集成电路动态存储器双倍数据速率时钟
文件页数/大小: 18 页 / 196 K
品牌: ELPIDA [ ELPIDA MEMORY ]
 浏览型号EBJ21EE8BAFA-8C-E的Datasheet PDF文件第10页浏览型号EBJ21EE8BAFA-8C-E的Datasheet PDF文件第11页浏览型号EBJ21EE8BAFA-8C-E的Datasheet PDF文件第12页浏览型号EBJ21EE8BAFA-8C-E的Datasheet PDF文件第13页浏览型号EBJ21EE8BAFA-8C-E的Datasheet PDF文件第14页浏览型号EBJ21EE8BAFA-8C-E的Datasheet PDF文件第16页浏览型号EBJ21EE8BAFA-8C-E的Datasheet PDF文件第17页浏览型号EBJ21EE8BAFA-8C-E的Datasheet PDF文件第18页  
EBJ21EE8BAFA  
CKE (input pin)  
CKE high activates, and CKE low deactivates, internal clock signals and device input buffers and output drivers.  
Taking CKE low provides precharge power-down and self-refresh operation (all banks idle), or active power-down  
(row active in any bank). CKE is asynchronous for self-refresh exit. After VREF has become stable during the  
power-on and initialization sequence, it must be maintained for proper operation of the CKE receiver. For proper  
self-refresh entry and exit, VREF must be maintained to this input. CKE must be maintained high throughout read  
and write accesses. Input buffers, excluding CK, /CK, ODT and CKE are disabled during power-down. Input  
buffers, excluding CKE, are disabled during self-refresh.  
DQ and CB (input and output pins)  
Bi-directional data bus.  
DQS and /DQS (input and output pin)  
Output with read data, input with write data. Edge-aligned with read data, centered in write data.  
The data strobe DQS is paired with differential signals /DQS to provide differential pair signaling to the system during  
READs and WRITEs.  
ODT (input pins)  
ODT (registered high) enables termination resistance internal to the DDR3 SDRAM. When enabled, ODT is only  
applied to each DQ, DQS, /DQS, DM. The ODT pin will be ignored if the mode register (MR1) is programmed to  
disable ODT.  
DM (input pins)  
DM is the reference signal of the data input mask function. DMs are sampled at the cross point of DQS and /DQS.  
VDD (power supply pins)  
1.5V is applied. (VDD is for the internal circuit.)  
VDDSPD (power supply pin)  
3.3V is applied (For serial EEPROM).  
VSS (power supply pin)  
Ground is connected.  
VTT (power supply pin)  
I/O termination supply for SDRAM.  
VREFDQ (power supply)  
Reference voltage for DQ.  
VREFCA (power supply)  
Reference voltage for CA.  
/RESET (input pin)  
/RESET is negative active signal (active low) and is referred to GND.  
/EVENT (output pin)  
Temperature alert output.  
Detailed Operation Part, Electrical Characteristics and Timing Waveforms  
Refer to the EDJ1104BASE, EDJ1108BASE, EDJ1116BASE datasheet (E1128E).  
Data Sheet E1235E40 (Ver. 4.0)  
15  
 复制成功!