STANDARD SPECIFICATIONS
Frequency Range:
Frequency Tolerance/Stability:
00
45
25
Operating Temperature Range
Blank
ET
Storage Temperature Range
Supply Voltage (V
EE
)
Input Current
Output Voltage Logic High
Output Voltage Logic Low
Rise/Fall Time
Duty Cycle
Load Drive Capability
Aging @ 25°C
Fine Leak Test:
Gross Leak Test:
Mechanical Shock:
Vibration:
Lead Integrity:
PIN
1
7
8
14
6.000MHz to 155.520MHz
(All Values Inclusive of Operating Temp. Range, Supply Voltage, and Load)
±100ppm Max.
±50ppm Max.
±25ppm Max. (0°C to +70°C only), (less than or equal to 125.000MHz only)
0°C to +70°C
-40°C to +85°C
-55°C to +125°C
-5.2Vdc ±5% (AA, AB, and AM); +5.2Vdc ±5% (AC)
140mA Maximum
-1.0Vdc Min./-0.7Vdc Max. (AA, AB, and AM); 4.0Vdc Min./4.5Vdc M ax. (AC)
-1.95Vdc Min./-1.60Vdc Max. (AA, AB, and AM); 3.00Vdc Min./3.42Vdc Max. (AC)
2nSec Maximum (Measured at 20% to 80% of waveform)
50% ±10% (Measured at 50% of waveform)
50 Ohms into -2.0Vdc (AA, AB, and AM); 50 Ohms into +3.0Vdc (AC)
±5ppm/year Maximum
OBSOLETE
ENVIRONMENTAL & MECHANICAL
MIL-STD-883, Method
MIL-STD-883, Method
MIL-STD-202, Method
MIL-STD-883, Method
MIL-STD-883, Method
1014, Condition A
1014, Condition C
213, Condition C
2007, Condition A
2004
Solderability:
Temperature Cycling:
Resistance to Soldering Heat:
Resistance to Solvents:
MIL-STD-883, Method 2002
MIL-STD-883, Method 1010
MIL-STD-202, Method 210
MIL-STD-202, Method 215
PIN CONFIGURATIONS
AA
Ground/Case
-5.2V
Output
Ground
AB
No Connect or Complementary Output
-5.2V
Output
Ground/Case
AC
No Connect or Complementary Output
Ground/Case
Output
+5.2Vdc
AM
No Connect or Complementary Output
Ground/Case
Output
-5.2Vdc
PART NUMBERING GUIDE
E11 00 AM ET C - 24.000M - CL175
Configuration Options
CLXXX = Cut Leads (MAL01-101-000)
G = Gull Wing (MAL01-001-000)
Frequency
Pin 1 Connection
Blank = No Connect
C = Complementary Output
Operating Temperature Range
Blank = 0°C to +70°C
ET = -40°C to +85°C
Pin Configuration
AA, AB, AC, or AM
Per Pin Configuration Table Above
Frequency Tolerance/Stability
00 = ±100ppm Maximum, 45 = ±50ppm Maximum
25 = ±25ppm Maximum
7.620
±0.203
1
15.240
±0.203
0.9 MAX
7
∅0.457
±0.1 (X4)
14
8
5.08
MAX
13.2
MAX
5.08
MIN
MARKING GUIDE
(Line #1)
ECLIPTEK
(Line #2)
E11 AM C
Pin 1 Connection
Blank = No Connect
C = Complementary Output
Pin Configuration Per Pin Configuration Table Above
20.8 MAX
ALL DIMENSIONS
IN MILLIMETERS
SPECIFICATION CONTROL DRAWING
Drawing Number
(Line #3)
XXX.XXXM
Frequency
CSC01-010-000
Title
(Line #4)
XX Y ZZ
Week of Year
Last Digit of Year
Ecliptek Manufacturing Code (TEN02-001-000)
ECLIPTEK
E11AMC
XXX.XXXM
XXYZZ
FULL SIZE ECL OSCILLATOR
Revision
Effectivity Date
E
ECN Number
08-27-03
PAGE 1 OF 2
Date Released By
Date
8675
NOTE: Pin 1 shall be marked with a black dot. Marking shall
conform to conditions listed in TQC41-001-000.
Approved By
ECLIPTEK [ ECLIPTEK CORPORATION ]
