欢迎访问ic37.com |
会员登录 免费注册
发布采购

DNT12S0A0S05NFA 参数 Datasheet PDF下载

DNT12S0A0S05NFA图片预览
型号: DNT12S0A0S05NFA
PDF下载: 下载PDF文件 查看货源
内容描述: 德尔福系列DNT12非隔离负载DC / DC电源模块的点: 8.3 〜 14Vin , 0.75 〜 5.5Vo , 3A [Delphi series DNT12 Non-Isolated Point of Load DC/DC Power Modules: 8.3~14Vin, 0.75~5.5Vo, 3A]
分类和应用: 电源电路
文件页数/大小: 12 页 / 730 K
品牌: DELTA [ DELTA ELECTRONICS, INC. ]
 浏览型号DNT12S0A0S05NFA的Datasheet PDF文件第4页浏览型号DNT12S0A0S05NFA的Datasheet PDF文件第5页浏览型号DNT12S0A0S05NFA的Datasheet PDF文件第6页浏览型号DNT12S0A0S05NFA的Datasheet PDF文件第7页浏览型号DNT12S0A0S05NFA的Datasheet PDF文件第9页浏览型号DNT12S0A0S05NFA的Datasheet PDF文件第10页浏览型号DNT12S0A0S05NFA的Datasheet PDF文件第11页浏览型号DNT12S0A0S05NFA的Datasheet PDF文件第12页  
FEATURE DESCRIPTIONS (CON.)  
FEATURE DESCRIPTIONS (CON.)  
The amount of power delivered by the module is the  
voltage at the output terminals multiplied by the output  
current. When using the trim feature, the output voltage  
of the module can be increased, which at the same  
output current would increase the power output of the  
module. Care should be taken to ensure that the  
maximum output power of the module must not exceed  
the maximum rated power (Vo.set x Io.max P max).  
Vtrim = 0.530V  
Voltage Margining  
Figure 24: Circuit configuration for programming output voltage  
Output voltage margining can be implemented in the  
DNT modules by connecting a resistor, Rmargin-up, from  
the Trim pin to the ground pin for margining-up the  
output voltage and by connecting a resistor, Rmargin-down,  
from the Trim pin to the output pin for margining-down.  
Figure 26 shows the circuit configuration for output  
voltage margining. If unused, leave the trim pin  
unconnected. A calculation tool is available from the  
evaluation procedure, which computes the values of  
Rmargin-up and Rmargin-down for a specific output voltage and  
margin percentage.  
using an external resistor  
Figure 25: Circuit Configuration for programming output voltage  
using external voltage source  
Table 1 provides Rtrim values required for some common  
output voltages, while Table 2 provides value of external  
voltage source, Vtrim, for the same common output  
voltages. By using a 1% tolerance trim resistor, set point  
tolerance of ±2% can be achieved as specified in the  
electrical specification.  
Vo  
Vin  
Rmargin-down  
Q1  
Trim  
GND  
On/Off  
Rmargin-up  
Q2  
Rtrim  
Table 1  
VO (V)  
0.7525  
1.2  
Rtrim (K)  
Open  
Figure 26: Circuit configuration for output voltage margining  
22.464  
13.047  
9.024  
1.5  
1.8  
2.5  
5.009  
3.3  
3.122  
5.0  
1.472  
5.5  
1.210  
Table 2  
VO (V)  
0.7525  
1.2  
Vtrim (V)  
Open  
0.670  
1.5  
0.650  
1.8  
0.630  
2.5  
0.583  
3.3  
0.530  
5.0  
5.5  
0.4167  
0.3840  
DS_DNT12SMD03_06252007  
8