欢迎访问ic37.com |
会员登录 免费注册
发布采购

CY7C68013A-56LFXI 参数 Datasheet PDF下载

CY7C68013A-56LFXI图片预览
型号: CY7C68013A-56LFXI
PDF下载: 下载PDF文件 查看货源
内容描述: EZ- USB FX2LP USB微控制器,高速USB外设控制器 [EZ-USB FX2LP USB Microcontroller High Speed USB Peripheral Controller]
分类和应用: 微控制器
文件页数/大小: 62 页 / 1626 K
品牌: CYPRESS [ CYPRESS SEMICONDUCTOR ]
 浏览型号CY7C68013A-56LFXI的Datasheet PDF文件第2页浏览型号CY7C68013A-56LFXI的Datasheet PDF文件第3页浏览型号CY7C68013A-56LFXI的Datasheet PDF文件第4页浏览型号CY7C68013A-56LFXI的Datasheet PDF文件第5页浏览型号CY7C68013A-56LFXI的Datasheet PDF文件第7页浏览型号CY7C68013A-56LFXI的Datasheet PDF文件第8页浏览型号CY7C68013A-56LFXI的Datasheet PDF文件第9页浏览型号CY7C68013A-56LFXI的Datasheet PDF文件第10页  
CY7C68013A, CY7C68014A
CY7C68015A, CY7C68016A
Table 4. Individual FIFO/GPIF Interrupt Sources
Priority
1
2
3
4
5
6
7
8
9
10
11
12
13
14
INT4VEC Value
80
84
88
8C
90
94
98
9C
A0
A4
A8
AC
B0
B4
Source
EP2PF
EP4PF
EP6PF
EP8PF
EP2EF
EP4EF
EP6EF
EP8EF
EP2FF
EP4FF
EP6FF
EP8FF
GPIFDONE
GPIFWF
Notes
Endpoint 2 Programmable Flag
Endpoint 4 Programmable Flag
Endpoint 6 Programmable Flag
Endpoint 8 Programmable Flag
Endpoint 2 Empty Flag
Endpoint 4 Empty Flag
Endpoint 6 Empty Flag
Endpoint 8 Empty Flag
Endpoint 2 Full Flag
Endpoint 4 Full Flag
Endpoint 6 Full Flag
Endpoint 8 Full Flag
GPIF Operation Complete
GPIF Waveform
5 ms after VCC reaches 3.0V. If the crystal input pin is driven by
a clock signal the internal PLL stabilizes in 200
μs
after VCC has
reached 3.0V.
applied during operation. A power on reset is defined as the time
reset that is asserted while power is being applied to the circuit.
A powered reset is when the FX2LP powered on and operating
and the RESET# pin is asserted.
Cypress provides an application note which describes and
recommends power on reset implementation. For more
information about reset implementation for the FX2 family of
products visit
If Autovectoring is enabled (AV4EN = 1 in the INTSET-UP
register), the FX 2LP substitutes its INT4VEC byte. Therefore, if
the high byte (“page”) of a jump-table address is preloaded at
location 0x0054, the automatically inserted INT4VEC byte at
0x0055 directs the jump to the correct address out of the 14
addresses within the page. When the ISR occurs, the FX2LP
pushes the program counter to its stack then jumps to address
0x0053, where it expects to find a “jump” instruction to the ISR
Interrupt service routine.
3.9 Reset and Wakeup
3.9.1 Reset Pin
The input pin, RESET#, resets the FX2LP when asserted. This
pin has hysteresis and is active LOW. When a crystal is used with
the CY7C680xxA the reset period must enable stabilization of
the crystal and the PLL. This reset period must be approximately
Note
3. If the external clock is powered at the same time as the CY7C680xxA and has a stabilization wait period, it must be added to the 200
μs.
Document #: 38-08032 Rev. *N
Page 6 of 62