欢迎访问ic37.com |
会员登录 免费注册
发布采购

CY7C68013A-100AXI 参数 Datasheet PDF下载

CY7C68013A-100AXI图片预览
型号: CY7C68013A-100AXI
PDF下载: 下载PDF文件 查看货源
内容描述: EZ- USB FX2LP⑩ USB微控制器,高速USB外设控制器 [EZ-USB FX2LP⑩ USB Microcontroller High-Speed USB Peripheral Controller]
分类和应用: 总线控制器微控制器和处理器外围集成电路数据传输可编程只读存储器电动程控只读存储器电可擦编程只读存储器时钟
文件页数/大小: 62 页 / 1649 K
品牌: CYPRESS [ CYPRESS SEMICONDUCTOR ]
 浏览型号CY7C68013A-100AXI的Datasheet PDF文件第3页浏览型号CY7C68013A-100AXI的Datasheet PDF文件第4页浏览型号CY7C68013A-100AXI的Datasheet PDF文件第5页浏览型号CY7C68013A-100AXI的Datasheet PDF文件第6页浏览型号CY7C68013A-100AXI的Datasheet PDF文件第8页浏览型号CY7C68013A-100AXI的Datasheet PDF文件第9页浏览型号CY7C68013A-100AXI的Datasheet PDF文件第10页浏览型号CY7C68013A-100AXI的Datasheet PDF文件第11页  
CY7C68013A, CY7C68014A
CY7C68015A, CY7C68016A
Figure 2. Reset Timing Plots
RESET#
RESET#
V
IL
3.3V
3.0V
VCC
0V
T
RESET
Power on Reset
V
IL
3.3V
VCC
0V
T
RESET
Powered Reset
Table 5. Reset Timing Values
Condition
Power on Reset with Crystal
Power on Reset with External
Clock
Powered Reset
3.9.2 Wakeup Pins
The 8051 puts itself and the rest of the chip into a power down
mode by setting PCON.0 = 1. This stops the oscillator and PLL.
When WAKEUP is asserted by external logic the oscillator
restarts after the PLL stabilizes, and the 8051 receives a wakeup
interrupt. This applies whether or not FX2LP is connected to the
USB.
The FX2LP exits the power down (USB suspend) state using one
of the following methods:
3.10 Program/Data RAM
T
RESET
5 ms
200
μs
+ Clock stability time
200
μs
3.10.1 Size
The FX2LP has 16 KBytes of internal program/data RAM, where
PSEN#/RD# signals are internally ORed to enable the 8051 to
access it as both program and data memory. No USB control
registers appear in this space.
Two memory maps are shown in the following diagrams:
3.10.2 Internal Code Memory, EA = 0
This mode implements the internal 16 KByte block of RAM
(starting at 0) as combined code and data memory. When
external RAM or ROM is added, the external read and write
strobes are suppressed for memory spaces that exist inside the
chip. This enables the user to connect a 64 KByte memory
without requiring address decodes to keep clear of internal
memory spaces.
Only the internal 16 KBytes and scratch pad 0.5 KBytes RAM
spaces have the following access:
USB bus activity (if D+/D– lines are left floating, noise on these
lines may indicate activity to the FX2LP and initiate a wakeup)
External logic asserts the WAKEUP pin
External logic asserts the PA3/WU2 pin
USB download
USB upload
Setup data pointer
I
2
C interface boot load.
The second wakeup pin, WU2, can also be configured as a
general purpose IO pin. This enables a simple external R-C
network to be used as a periodic wakeup source. WAKEUP is by
default active LOW.
3.10.3 External Code Memory, EA = 1
The bottom 16 KBytes of program memory is external and
therefore the bottom 16 KBytes of internal RAM is accessible
only as a data memory.
Document #: 38-08032 Rev. *L
Page 7 of 62