欢迎访问ic37.com |
会员登录 免费注册
发布采购

BCM20710A1KUBXG 参数 Datasheet PDF下载

BCM20710A1KUBXG图片预览
型号: BCM20710A1KUBXG
PDF下载: 下载PDF文件 查看货源
内容描述: [Bluetooth 4.0 EDR compliant]
分类和应用:
文件页数/大小: 50 页 / 4157 K
品牌: CYPRESS [ CYPRESS ]
 浏览型号BCM20710A1KUBXG的Datasheet PDF文件第1页浏览型号BCM20710A1KUBXG的Datasheet PDF文件第2页浏览型号BCM20710A1KUBXG的Datasheet PDF文件第3页浏览型号BCM20710A1KUBXG的Datasheet PDF文件第5页浏览型号BCM20710A1KUBXG的Datasheet PDF文件第6页浏览型号BCM20710A1KUBXG的Datasheet PDF文件第7页浏览型号BCM20710A1KUBXG的Datasheet PDF文件第8页浏览型号BCM20710A1KUBXG的Datasheet PDF文件第9页  
PRELIMINARY  
CYW20710  
1. Overview  
The Cypress CYW20710 complies with the Bluetooth Core Specification, version 4.0 and is designed for use with a standard Host  
Controller Interface (HCI) UART. The combination of the Bluetooth Baseband Core (BBC), a Peripheral Transport Unit (PTU), and an  
ARM®-based microprocessor with on-chip ROM provides a complete lower layer Bluetooth protocol stack, including the Link Controller  
(LC), Link Manager (LM), and HCI.  
1.1 Major Features  
Major features of the CYW20710 include:  
Support for Bluetooth 4.0 + EDR, including the following options:  
A whitelist size of 25.  
Enhanced Power Control  
HCI Read Encryption Key Size command  
Full support for Bluetooth 2.1 + EDR additional features:  
Secure Simple Pairing (SSP)  
Encryption Pause Resume (EPR)  
Enhance Inquiry Response (EIR)  
Link Supervision Time Out (LSTO)  
Sniff SubRating (SSR)  
Erroneous Data (ED)  
Packet Boundary Flag (PBF)  
Built-in Low Drop-Out (LDO) regulators (2)  
1.63 to 5.5V input voltage range  
1.8 to 3.3V intermediate programmable output voltage  
Integrated RF section  
Single-ended, 50 ohm RF interface  
Built-in TX/RX switch functionality  
TX Class 1 output power capability  
-88 dBm RX sensitivity basic rate  
Supports maximum Bluetooth data rates over HCI UART and SPI interfaces  
Multipoint operation, with up to 7 active slaves  
Maximum of 7 simultaneous active ACL links  
Maximum of 3 simultaneous active SCO and eSCO links, with Scatternet support  
Scatternet operation, with up to 4 active piconets (with background scan and support for ScatterMode)  
High-speed HCI UART transport support  
H4 five-wire UART (four signal wires, one ground wire)  
H5 three-wire UART (two signal wires, one ground wire)  
Maximum UART baud rates of 4 Mbps  
Low-power out-of-band BT_WAKE and HOST_WAKE signaling  
VSC from host transport to UART  
Proprietary compressing scheme (allows more than two simultaneous A2DP packets and up to five devices at a time)  
Channel Quality-Driven Data Rate (CQDDR) and packet type selection  
Standard Bluetooth test modes  
Extended radio and production test mode features  
Document No. 002-14804 Rev. *H  
Page 4 of 50  
 复制成功!