欢迎访问ic37.com |
会员登录 免费注册
发布采购

CBC915-ACA777 参数 Datasheet PDF下载

CBC915-ACA777图片预览
型号: CBC915-ACA777
PDF下载: 下载PDF文件 查看货源
内容描述: 的EnerChip EP通用能量收集EVAL KIT [EnerChip EP Universal Energy Harvester Eval Kit]
分类和应用:
文件页数/大小: 15 页 / 1102 K
品牌: CYMBET [ CYMBET CORPORATION ]
 浏览型号CBC915-ACA777的Datasheet PDF文件第1页浏览型号CBC915-ACA777的Datasheet PDF文件第2页浏览型号CBC915-ACA777的Datasheet PDF文件第3页浏览型号CBC915-ACA777的Datasheet PDF文件第5页浏览型号CBC915-ACA777的Datasheet PDF文件第6页浏览型号CBC915-ACA777的Datasheet PDF文件第7页浏览型号CBC915-ACA777的Datasheet PDF文件第8页浏览型号CBC915-ACA777的Datasheet PDF文件第9页  
CBC-EVAL-09 EnerChip EP Universal EH Eval Kit  
EVAL-09 Module Connector and Test Point Explanations  
The purpose and use of the connectors identified in Figure 3 and in the previous tables are:  
J1, J2, J8, J11, J13, J14 Connectors - not user accessible.  
J3 Connector - EnerChip EP pins 1-19 probe points and access vias.  
J4 Connector - EnerChip EP pins 20-38 probe points and access vias.  
J5, J6 Connectors - EVAL-09 debug interface connectors for development system access. Contact Cymbet  
Applications Engineering for additional details if required.  
J7 Connector - Bypass diode circular pad trace to select an optional external rechargeable lithium battery  
with 4.1V charging voltage.  
J9 Connector - Six pin right angle connector for serial port, Vout and Ground. Normally used for connection to  
TI eZ430-RF2500 wireless end device or another target system.  
J10 Connector - Five pin vertical connector for user access to serial port, Vout and Ground.  
J12 Connector - Access vias for an optional external rechargeable lithium battery with 4.1V charging voltage.  
J15 Connector - High Voltage DC Input from EH Transducer such as a thermoelectric generator (TEG).  
J16 Connector - High Voltage AC Input 1 normally used by a piezoelectric EH transducer.  
J17 Connector - High Voltage AC Input 2 normally used by a piezoelectric EH transducer .  
J18 Connector - Low voltage DC Input normally used by a photovoltaic cell.  
J19 Connector - Low voltage AC Input normally used by a thermoelectric generator or electromagnetic  
generator.  
Cable Assembly - A 5-conductor cable with a header connector at each end is provided with CBC-EVAL-09 to  
facilitate connection between the J5 connector and a 5-pin header on the user’s board.  
TP1 - the output of the boost converter or FLYBACK converter capacitor. Typical value is 4.06V.  
TP2 - EPVCC - Voltage used to power the CBC915 device should be 3.6V  
TP3, TP3, TP5 - Ground  
TP6 – VCAP – voltage of the output capacitor should be 3.6V  
TP7– VOUT – output voltage to the target system should be 3.6V  
TP8 – VBAT – output of battery cut-off circuit should be 4.06V  
TP9 – VEC – EnerChip output voltage feeding battery cutoff circuit should be in the range of 4.06VDC to  
3.0VDC. Caution: do not leave voltmeter or scope probes attached to this TP. Will discharge EnerChip.  
TP10 – HV V In – DC voltage from the HV DC In or HV AC1 IN or HV AC2 IN ports  
TP11 – V In – DC voltage from the DC In or AC1 IN ports  
©2013 Cymbet Corporation • Tel: +1-763-633-1780 • www.cymbet.com  
DS-72-13 Rev G  
Page 4 of 15