2111 Comprehensive Drive
Aurora, Illinois 60505
Phone: 630- 851- 4722
Fax: 630- 851- 5040
www.conwin.com
Package Characteristics
Package
Hermetically sealed ceramic package and metal cover
Test Circuit
OSCILLOSCOPE
POWER
SUPPLY
Environmental Characteristics
Temperature Cycle: The specimen shall meet electrical characteristics after
tested 5 cycles of -55°C / 30 minutes and +125°C / 30 minutes
Hermetical:
No bubbles appear in Flourinert (FC-43) at 125°C ±5°C for 5 minutes
Solvent Resistance:
Marking will withstand immersion in
Isopropyl Alcohol or Trichloroethylene
PROBE
OSC
FREQ
COUNTER
INPUT FOR E/D
Soldering
260°C max x 10 sec max x 2 times max or
230°C max x 180 sec max x 1 time
Typical Operation Data
(Vapor phase reflow)
20 to 100 sec up to 215°C, 50 sec at 215°C,
then down to room temperature per 1 to 5°C / sec
General Conditions
Output Waveform
Mechanical Characteristics
The specimen shall meet electrical characteristics after tested 3 times,
Free Drop testing on the hard wooden board from a height of 75 cm.
Vibration:
The specimen shall meet electrical characteristics after tested
by the following conditions: 10-55Hz 1.5mm Amplitude,
55-2000 Hz 20 G's, 2 hours for each plane
Thermal Shock: After applied Thermal Shock of 260°C max x 10 sec max x 2 times,
or 230°C max x 180 sec max, the specimen shall meet electrical characteristics
Solderability:
(EIAJ-RCX-0102.101 Condition 1a)
1) Flux: MIL-F-14256 (WW Rosin=25%, Isopropyl Alcohol = 75%)
2) Solder: QQ-S-571 (Sn = 63%, Pb = 37%)
3) Solder bath temperature: 235°C ±5°C
4) Depth of immersion: Up to electrical terminal
5) Immersing time: Within 2 sec ±0.5 sec into solder bath
After performing the above procedures, a newly soldered coverage shall be
greater than 90%
Free Drop:
SYMMETRY
Suggested Pad Layout
Bypass capacitor, C-by, should
be ceramic capacitor
≥
.01uf.
Ordering Information
7
Type
Clock
3.2x5.0mm
Package
1
Temperature
Range
1 = 0 to 70°C
4 = -20 to 70°C
1
Frequency
Tolerance
1=
2=
3=
4=
±25 ppm
±50 ppm
±100 ppm
±20 ppm
3
Supply Voltage
3 = 3.3 Vdc
050.0M
Output Frequency
Frequency Format
-xxx.xM Minimum
-xxx.xxxxxxM Maximum
*Amount of numbers after
the decimal point.
M = MHz
Pad Connections
Pad Connection
1: Enable / Disable
2: Ground
3: Output
4: Vcc
Example to order a 7113 with an output frequency of:
4 MHz = 7113-004.0M
44.736 MHz = 7113-044.736M
125 MHz = 7113-125.0M
Package Outline
.53
(13.5mm)
.217
(5.5mm)
8.46 DIA
(215mm)
.08
(2.0mm)
.08
(2.0mm)
(3.7mm)
.157
(4.0mm)
.15
9.84
(250mm)
Dimensional Tolerance: ± .02" (.508mm)
± .005" (.127mm)
.08
(2.0mm)
3.15
3.15
(80mm)
(80mm)
.06
(1.5mm)
1.00 DIA
(25mm)
Dimensional Tolerance: ±.02" (.508mm)
Dimensional Tolerance: ±.02” (.508mm)
±.005” (.127mm)
±.005" (.127mm)
.217
(5.5mm)
7113 6B
50MHz
Bulletin
Page
Revision
Date
Tape and Reel Dimensions
.07
Meets EIA-481A and EIAJ-1009B
2,000 PCS/REEL
(1.75mm)
.47
(12.0mm)
Sm087
2 of 2
05
23 Feb 2016
Specifications subject to change without notification. See Connor-Winfield's website for latest revision. All dimensions in inches.
© Copyright 2016 The Connor-Winfield Corporation
Not intended for life support applications.
CONNOR-WINFIELD [ CONNOR-WINFIELD CORPORATION ]
