RF210(A/B)
Image-Reject Downconverter
of the mixer gain can be accomplished by varying the quiescent
current on the ADJMIX pin (Pin 11). This pin can be connected
to VCC or ground through resistors. The current will increase if
the pin is connected to GND and decrease if connected to VCC.
For optimal performance, this pin should be left unconnected.
Technical Description
The RF210(A/B) dual-band, image-reject downconverters
implement the front-end functions of a dual-band super-
heterodyne receiver. These devices consist of two receive
paths, one for GSM900 and the other for DCS1800 (or
PCS1900). Each receive path contains an LNA and an image-
reject mixer. The IF and LO ports are common to both receive
paths. The image-reject mixers can provide 30 dB of image
rejection for both the GSM900 and the DCS1800 (or PCS1900)
bands without using any post-LNA image reject filters.
The band of operation for RF210(A/B) is selected by the
BANDSEL signal on Pin 14. It switches the receive path
between GSM900 and DCS1800 (or PCS1900) bands.
The device can operate from a three-cell battery pack (2.7 V to
µ
5.0 V). Standby mode current is extremely low at 20 A, which
maximizes handset standby time.
The LNA/mixer combination has a switchable gain. The RF210A
and RF210B both have 22 dB of gain in the high gain mode. For
the RF210A, the gain is reduced by 10 dB (GSM band) and by
8 dB (DCS/PCS band) in the low gain mode. For the RF210B,
the gain is reduced by 20 dB (GSM band) and by 16 dB
(DCS/PCS band) in the low gain mode. The gain mode is
selected using the GAINSEL pin (Pin 7). Low gain mode is
selected by driving the GAINSEL signal high; high gain mode is
selected by driving the signal low. In addition, small adjustments
The signal pin assignments and functional pin descriptions are
found in Table 1. The absolute maximum ratings of the
RF210(A/B) are provided in Table 2, the operating conditions
are specified in Table 3, and electrical specifications are
provided in Table 4. Figure 3 shows the diagram for a typical
application circuit using the RF210(A/B) downconverter. Figure
4 provides the package dimensions for the 20-pin TSSOP
device and Figure 5 provides the tape and reel dimensions.
Table 1. RF210(A/B) Signal Description
Pin #
Name
Description
Pin #
Name
ADJMIX
Description
Mixer bias adjust pin
1
2
NC
No connect
11
12
LNA900GND
BIASGND
LNA900IN
BIASVCC
LNAVCC
900 MHz LNA ground
Bias ground
LOGND
LOIN
LO input ground
3
4
13
14
15
16
17
18
19
20
LO input
900 MHz LNA input
Bias supply
BANDSEL
BYP1800
IFOUT–
IFOUT+
BYP900
MIXGND
MIXVCC
Band selection pin
5
Bypass capacitor for 1800 MHz band
Mixer output (negative)
Mixer output (positive)
Bypass capacitor for 900 MHz band
Mixer ground
6
LNA supply
7
GAINSEL
LNA1800IN
LNA1800GND
ENA
LNA gain select
8
1800 MHz LNA input
1800 MHz LNA ground
Device enable (active high)
9
10
Mixer supply
Table 2. Absolute Maximum Ratings
Parameter
Minimum
Maximum
Units
Storage Temperature
LNA Input Power
–40
+125
+5
°C
dBm
V
Supply Voltage (VCC)
Input Voltage Range
–0.3
–0.3
+6
Vcc
V
2
Conexant
100775A
October 20, 1999
Proprietary Information and Specifications are Subject to Change
CONEXANT [ CONEXANT SYSTEMS, INC ]
