Specification
Absolute Maximum Ratings
Exceeding the maximum rating can result in device damage. Operation of the device outside the operating limits is
not implied.
Supply voltage
-0.3 to 7.0V
Input voltage at any pin (ref V
SS
= 0V)
-0.3 to (V
DD
+ 0.3V)
Sink/source current (supply pins)
+/- 30mA
(other pins)
+/- 20mA
Total device dissipation @ T
AMB
25°C
800mW Max.
Derating
10mW/°C
Storage temperature range:
FX613DW/P
-40°C to +85°C (plastic)
Operating Limits ......
Min.
Max.
Unit
Supply Voltage (V
DD
)
3.0
5.5
V
at 25°C
Operating Temperature ......
-40
+85
°C
All device characteristics are measured under the following conditions unless otherwise specified:
V
DD
= 3.3V, T
OP
= -40 to +85 °C. Audio Level 0dB ref: = 775mVrms. Xtal/Clock Frequency = 3.579545MHz
Characteristics
See Note
Min.
-
70.0
0
90.0
-
10.0
-
-
-
-
-
Typ.
0.3
-
-
-
-
-
50.0
210
-
500
-
Max.
1.0
100
30.0
100
10.0
-
-
-
500
-
2.5
Unit
mA
% V
DD
% V
DD
% V
DD
% V
DD
MΩ
kΩ
kΩ
Ω
Ω
kΩ
Static Values
Supply Current
Input Logic “1”
Input Logic “0”
Output Logic “1”
1
Output Logic “0”
1
Impedances
Chip Select and Serial Clock Input
Signal Input
Level Input
IRQ Output (logic “0”)
Data Output (logic “0”)
(Logic “1”)
Dynamic Values
On-Chip Xtal Oscillator
R
IN
R
OUT
DC Voltage Gain
Bandwidth at Unity Gain
Single Tone Operation
Must-Decode Input Level
2
Must-Not Decode Input Level
2
LO Band Frequency Range
4
HI Band Frequency Range
4
Frequency Resolution (Table 1)
LO Band
HI Band
Input Signal/White-Noise Ratio (HI & LO Bands)
Interrupt Rate (LO Band)
3
(HI Band)
3
False Decodes Due to Noise
6
Outband modulation level limits
for correct decode (f
IN
= 340Hz to 620Hz)
5
Notes
1.
2.
3.
4.
5.
6.
10.0
-
25.0
5.0
-25.2
-
300
900
-
-
-
19.0
57.0
-
-
-
230
42.0
11.0
-
-
-
825
-
-
-
-46.0
660
2150
25.0
75.0
-
-
-
-
10.0
MΩ
kΩ
V/V
MHz
dB
dB
Hz
Hz
Hz
Hz
dB
/sec
/sec
/2 secs
%
-
-
18.0
-
-
1.0
-
Into a high-impedance load
(>1.0MΩ)
.
Must decode signal above -25.2dB; Must Not decode signal below -46.0dB.
If a supply other than 3.3 volts is used, levels will change pro-rata.
Under ‘Pure Tone’ input conditions.
For input frequencies of between 661Hz and 899Hz the FX613 will provide no reliable output.
With an amplitude modulating frequency of between 16.0Hz and 100Hz.
Test noise input = 5.0kHz at 100mVrms
7
CMLMICRO [ CML MICROCIRCUITS ]
