欢迎访问ic37.com |
会员登录 免费注册
发布采购

CMX869BD2 参数 Datasheet PDF下载

CMX869BD2图片预览
型号: CMX869BD2
PDF下载: 下载PDF文件 查看货源
内容描述: [Modem, PDSO24, SOIC-24]
分类和应用: 光电二极管
文件页数/大小: 49 页 / 1116 K
品牌: CMLMICRO [ CML MICROCIRCUITS ]
 浏览型号CMX869BD2的Datasheet PDF文件第7页浏览型号CMX869BD2的Datasheet PDF文件第8页浏览型号CMX869BD2的Datasheet PDF文件第9页浏览型号CMX869BD2的Datasheet PDF文件第10页浏览型号CMX869BD2的Datasheet PDF文件第12页浏览型号CMX869BD2的Datasheet PDF文件第13页浏览型号CMX869BD2的Datasheet PDF文件第14页浏览型号CMX869BD2的Datasheet PDF文件第15页  
Low-Power V.32 bis Modem  
CMX869B  
In the receive direction, the signal detection thresholds within the CMX869B are proportional to AVDD and  
are affected by the Rx Gain Control gain setting in the Rx Mode Register. The signal level into the  
CMX869B is affected by the line coupling transformer loss and the values of R11 and R12 of Figure 4a.  
The value of R11 should be chosen so that the received signal level at the RXAFB pin is 3.6dB lower than  
that on the 2-wire line. For example if the transformer loss is 1dB then R11 should be 130kΩ. The value of  
R14 (15kΩ) is chosen to apply approximately 20dB of extra gain, when required by Type 1 Caller Line  
Identification.  
For best Rx performance, it is recommended that the transformer coupling arrangement should provide at  
least 7dB trans-hybrid loss.  
The RXBN input can be selected by setting bit 14 of the General Control Register to 1, which internally  
connects RXBN to RXAN. With the components shown in Figures 4a and 4b, this will add approximately  
20dB to the Rx gain, by connecting R14 in parallel with R11. This facilitates detection of certain signals  
whilst on-hook, such as may be required for Type 1 Caller Line Identification reception. For the 2-wire line  
interface shown in Figure 4a, capacitor C12 is required to provide an AC path through to the device when  
the relay is open. If this facility is not required, R14 and C12 can be omitted.  
4-Wire Line Interface  
Figure 4b shows a simplified interface for use with a 600Ω 4-wire line. The line terminations are provided  
by R10 and R13, high frequency noise is attenuated by C11 while R11 and R12 set the receive signal  
level into the modem. Transmit and receive line level settings and the values of R11 and R14 are as for  
the 2-wire circuit.  
RXAFB  
C11  
R12  
R14  
RXBN  
RXAN  
RXA  
C12  
1:1  
-
+
R11  
R13  
Rx  
Tx  
R10  
V
BIAS  
C3  
4-Wire  
Line  
AVSS  
CMX869B  
AVSS  
TXA  
TXAN  
R10, 13  
R11  
R12  
C3  
C11  
C12  
See Figure 2  
100pF  
33nF  
600Ω  
130kΩ (see text)  
100kΩ  
R14  
15kΩ (see text)  
Resistors ±5%, capacitors ±20%  
Figure 4b 4-Wire Line Interface Circuit  
© 2008 CML Microsystems Plc  
11  
D/869B/3