IXD_614
5.4.3 YI (5-Pin TO-263)
1.20 / 1.40
(0.047 / 0.055)
1.00 / 1.40
(0.039 / 0.055)
Recommended PCB Pattern
4.20 / 4.80
(0.165 / 0.189)
9.65 / 10.30
(0.380 / 0.406)
10.40
(0.409)
9.15
(0.360)
8.80 / 9.50
(0.346 / 0.374)
3.65
(0.144)
14.80 / 15.80
(0.583 / 0.622)
1
2 3 4 5
6.35
(0.250)
3.85
(0.152)
0.40 / 0.70
(0.016 / 0.028)
1.70 BSC
(0.067 BSC)
1.70
(0.067)
1.05
(0.041)
0.60 / 0.99
(0.024 / 0.039)
2.24 / 2.84
(0.088 / 0.112)
7.50 / 8.20
(0.295 / 0.323)
Optional
0º - 3º
6.60 / 7.20
(0.260 / 0.283)
DIMENSIONS
mm MIN / mm MAX
(inches MIN / inches / MAX)
2.10 / 2.70
(0.083 / 0.106)
6
NOTES:
1. All metal surfaces are solder-plated except trimmed area.
2. Short lead of No. 3 is optional to IXYS.
3. No. 3 lead is connected to No. 6 lead (bottom heat sink) internally.
1.20 / 1.70
(0.047 / 0.067)
5.4.4 CI (5-Pin TO-220)
1.14 / 1.40
(0.045 / 0.055)
9.91 / 10.54
(0.390 / 0.415)
4.32 / 4.83
(0.170 / 0.190)
7.823
(0.308)
12.387
(0.487)
14.73 / 15.75
(0.580 / 0.620)
11.94 / 12.95
(0.470 / 0.510)
6.299
(0.248)
8.64 / 9.40
(0.340 / 0.370)
3
1
2 3 4 5
6.502
(0.256)
7.620
(0.300)
DIMENSIONS
mm MIN / mm MAX
(inches MIN / inches / MAX)
25.27 / 26.54
(0.995 / 1.045)
12.70 / 14.73
(0.50 / 0.58)
0.38 / 0.64
(0.015 / 0.025)
2.29 / 2.92
1.70 BSC
(0.067 BSC)
0.64 / 1.02
(0.025 / 0.040)
Recommended Hole Pattern
(0.090 / 0.115)
Finished Hole Diameter = 1.45mm (0.057 in.)
NOTES:
1.This drawing will meet all dimensions requirement of
JEDEC outlines TS-001AA and 5-lead version TO-220AB.
2. Mounting hole diameter: 3.53 / 3.96 (0.139 / 0.156)
3.The metal tab is connected to pin 3 (GND).
1.70mm (0.067 in.)
R02
www.clare.com
13
CLARE [ CLARE ]
