CPC7691
2.9 Protection
If a power-cross fault occurs with the device in the talk
state, the current is passed though the break switches
SW1 and SW2 on to the integrated protection circuit
but is limited by the dynamic DC current limit response
of the two break switches. The DC current limit
specified over temperature is between 80 mA and
425 mA and the circuitry has a negative temperature
coefficient. As a result, if the device is subjected to
extended heating due to a power cross fault condition,
2.9.1 Diode Bridge/SCR
The CPC7691 uses a combination of current limited
break switches, a diode bridge/SCR clamping circuit,
and a thermal shutdown mechanism to protect the
SLIC device or other associated circuitry from damage
during line transient events such as lightning. During a
positive transient condition, the fault current is
the measured current into T
or R
will decrease
conducted through the diode bridge to ground via
LINE
LINE
F
. Voltage is clamped to a diode drop above
as the device temperature increases. If the device
temperature rises sufficiently, the temperature
shutdown mechanism will activate and the device will
enter the all-off state.
GND
ground. During a negative transient of 2 to 4 V more
negative than the voltage source at V , the SCR
conducts and faults are shunted to F
or the diode bridge.
BAT
via the SCR
GND
2.10 Thermal Shutdown
The thermal shutdown mechanism activates when the
device die temperature reaches a minimum of 110° C,
placing the device in the all-off state regardless of
In order for the SCR to crowbar (or foldback), the
SCR’s on-voltage (see “Protection Circuitry Electrical
Specifications” on page 9) must be less than the applied
logic input. During thermal shutdown events the T
SD
voltage at the V
pin. If the V
voltage is less
BAT
BAT
pin will output a logic low with a nominal 0 V level. A
logic high is output from the T pin during normal
negative than the SCR on-voltage, or if the V
BAT
SD
supply is unable to source the trigger current, the SCR
will not crowbar.
operation with a typical output level equal to V
.
DD
If presented with a short duration transient such as a
lightning event, the thermal shutdown feature will
typically not activate. But in an extended power-cross
event, the device temperature will rise and the thermal
shutdown mechanism will activate forcing the switches
to the all-off state. At this point the current measured
For power induction or power-cross fault conditions,
the positive cycle of the transient is clamped to a diode
drop above ground and the fault current is directed to
ground. The negative cycle of the transient will cause
the SCR to conduct when the voltage exceeds the
V
reference voltage by two to four volts, steering
BAT
into T
or R
will drop to zero. Once the device
LINE
LINE
the fault current to ground.
enters thermal shutdown it will remain in the all-off
state until the temperature of the device drops below
the de-activation level of the thermal shutdown circuit.
This permits the device to autonomously return to
normal operation. If the transient has not passed,
current will again flow up to the value allowed by the
dynamic DC current limiting of the switches and
heating will resume, reactivating the thermal shutdown
mechanism. This cycle of entering and exiting the
thermal shutdown mode will continue as long as the
fault condition persists. If the magnitude of the fault
condition is great enough, the external secondary
protector will activate shunting the fault current to
ground.
Note: The CPC7691xB does not contain the
protection SCR but instead uses diodes to clamp both
polarities of a transient fault. These diodes direct the
negative potential’s fault current to the V
pin.
BAT
2.9.2 Current Limiting function
If a lightning strike transient occurs when the device is
in the talk state, the current is passed along the line to
the integrated protection circuitry and restricted by the
dynamic current limit response of the active switches.
During the talk state when a 1000V 10x1000 μs
lightning pulse (GR-1089-CORE) is applied to the line
though a properly clamped external protector, the
current seen at T
or R
will be a pulse with a
LINE
LINE
typical magnitude of 2.5 A and a duration less than
0.5 μs.
14
PRELIMINARY
R00E
CLARE [ CLARE ]
