CPC7583
Absolute Maximum Ratings are stress ratings. Functional op-
eration of the device at these or any other conditions beyond
those indicated in the operational sections of this data sheet is
not implied. Exposure of the device to the absolute maximum
ratings for extended period may degrade the device and effect
its reliability.
Parameter
Min
-40
-40
5
Max
+110
+150
95
Units
˚C
˚C
%
˚C
Operating Temperature Range
Storage Temperature Range
Relative Humidity Range
Pin Soldering Temperature
(t=10 s max)
-
+260
+5V Power Supply
Battery Supply
Logic Input Voltage
Logic Input to Switch Output Isolation
Switch Isolation (SW1, SW2, SW3,
SW5, SW6, SW7, SW9,SW10)
Switch Isolation (SW4)
Switch Isolation (SW8)
-
-
-
-
-
7
-85
7
330
330
V
V
V
V
V
-
-
480
235
V
V
Electrical Characteristics TA = -40oC to +85oC (unless otherwise specified)
Minimum and maximum values are production testing requirements. Typical values are characteristic of the device and are the result
of engineering evaluations. Typical values are provided for information purposes only and are not part of the testing requirements.
Power Supply Specifications
Supply
Min
+4.5
-19
Typ
+5.0
-
Max
+5.5
-72
Unit
V
V
ESD Rating (HBM Model)
VDD
VBAT
1000
1
1 VBAT is used only as a reference for internal protection circuitry.
If VBAT rises above -10V, the device will enter an all off state and will remain in the all off state until the battery voltage drops below -15V.
Table 1. Break Switch, SW1 and SW2
PARAMETERS
CONDITIONS
SYMBOL
Isw
MIN
TYP
0.1
0.3
0.1
MAX
UNITS
µA
Off-state Leakage Current:
o
+25 C
Vsw (differential)= -320V to Gnd
Vsw (differential)= -60V to +260V
Vsw (differential)= -330V to Gnd
Vsw (differential)= -60V to +270V
Vsw (differential)= -310V to Gnd
Vsw (differential)= -60V to +250V
-
-
-
1
1
1
o
+85 C
Isw
µA
o
-40 C
Isw
µA
RDS (SW1,SW2):
ON
o
+25 C
TLINE= +/-10 mA, +/-40mA, TBAT= -2V
TLINE= +/-10 mA, +/-40mA, TBAT= -2V
TLINE= +/-10 mA, +/-40mA, TBAT= -2V
Per ON-resistance Test Condition of
SW1, SW2
∆ V
∆ V
∆ V
-
-
-
-
14.5
20.5
10.5
0.15
-
28
-
Ω
Ω
Ω
Ω
o
+85 C
o
-40 C
RDS Match
ON
Magnitude
RON SW1-RONSW2
0.8
DC Current Limit:
o
+25 C
Vsw (on) = +/- 10V
Vsw (on) = +/- 10V
Vsw (on) = +/- 10V
Break switches in ON state, ringing
access switches OFF, apply +/- 1000V
at 10/1000µs pulse, appropriate
secondary protection in place.
Isw
Isw
Isw
Isw
-
80
-
225
150
400
2.5
-
-
mA
mA
mA
A
o
+85 C
o
-40 C
425
-
Dynamic Current Limit:
(t=<0.5µs)
-
Logic Input to Switch Output Isolation:
o
+25 C
Vsw (TLINE, RLINE) = +/-320V
Isw
Isw
Isw
-
-
-
-
-
0.1
0.3
0.1
200
1
1
1
-
µA
µA
Logic Inputs = Gnd
Vsw (TLINE, RLINE) = +/-330V
Logic Inputs = Gnd
Vsw (TLINE, RLINE) = +/-310V
Logic Inputs = Gnd
-
o
+85 C
o
-40 C
µA
dv/dt Sensitivity1
1 Applied voltage is 100 Vp-p square wave at 100Hz.
V/µs
Rev. E
2
www.clare.com
CLARE [ CLARE ]
