CONDUCTIVE POLYMER ALUMINUM SOLID CAPACITORS
NPCAP
TM
Radial Lead
-
・Super
low ESR, high ripple current capability
・Rated
voltage range : 2.5 to 16V
dc
・Nominal
capacitance range : 270 to 2,700μF
・Endurance
: 15,000 hours at 105℃
・Suitable
for DC-DC converters, voltage regulators and decoupling applications
for computer motherboards
・Added
2.5V 820μF (ESR 5mΩ max.)
・Solvent
resistant type (see PRECAUTIONS AND GUIDELINES)
・RoHS2
Compliant
・Halogen
Free
PSC
Series
PSE P2-42
Longer life
Downsizing
PSC
◆SPECIFICATIONS
Items
Category
Temperature Range
Rated Voltage Range
Capacitance Tolerance
Surge Voltage
Leakage Current
*Note
Characteristics
-55 to +105℃
2.5 to 16V
dc
±20%
(M)
Rated voltage×1.15
I=0.2CV or 500μA, whichever is greater.
Where, I : Max. leakage current (μA), C : Nominal capacitance (μF), V : Rated voltage (V
dc
)
0.10 max.
Z(-25℃)/Z(+20℃)≦1.15
Z(-55℃)/Z(+20℃)≦1.25
(at 20℃, 120Hz)
(at 105℃)
(at 20℃ after 2 minutes)
(at 20℃, 120Hz)
Dissipation Factor
(tanδ)
Low Temperature
Characteristics
(Max.Impedance Ratio)
Endurance
Bias Humidity Test
Surge Voltage Test
Failure Rate
(at 100kHz)
The following specifications shall be satisfied when the capacitors are restored to 20℃ after the rated voltage is applied for 15,000 hours
at 105℃.
Appearance
No significant damage
Capacitance change
≦±20%
of the initial value
D.F. (tanδ)
≦150%
of the initial specified value
ESR
≦150%
of the initial specified value
Leakage current
≦The
initial specified value
The following specifications shall be satisfied when the capacitors are restored to 20℃ after subjecting them to DC voltage at 60℃,
90 to 95% RH for 1,000 hours.
Appearance
No significant damage
Capacitance change
≦±20%
of the initial value
D.F. (tanδ)
≦150%
of the initial specified value
ESR
≦150%
of the initial specified value
Leakage current
≦The
initial specified value
The capacitors shall be subjected to 1,000 cycles each consisting of charge with the surge voltage specified at 105℃ for 30 seconds
through a protective resistor(R=1kΩ) and discharge for 5 minutes 30 seconds.
Appearance
No significant damage
Capacitance change
≦±20%
of the initial value
D.F. (tanδ)
≦150%
of the initial specified value
ESR
≦150%
of the initial specified value
Leakage current
≦The
initial specified value
0.5% per 1,000 hours maximum (Confidence level 60% at 105℃)
*Note : If any doubt arises, measure the leakage current after the following voltage treatment.
Voltage treatment : DC rated voltage is applied to the capacitors for 120 minutes at 105℃.
◆DIMENSIONS
[mm]
●
Terminal
Code : E
φd
F
±
0.5
◆MARKING
EX) 2.5V820µF
Coated Case
L'
15min.
4min.
Size code
H08
φD
8.0
φd
0.6
F
3.5
φD'
L'
L+1.0max.
HB5
JB5
8.0
10.0
0.8(Note1)
0.8(Note1)
3.5
5.0
φD+0.5max.
L+1.5max.
JC5
10.0
0.6
5.0
C
3D6
820
2.5
V
φD'
Note1 : 0.6 for rated volt 16V.
Product specifications in this catalog are subject to change without notice.Request our product specifications before purchase and/or use. Please use our products based on the information contained in this catalog and product specifications.
2-44
CAT. No. E1001R
CHEMI-CON [ UNITED CHEMI-CON, INC. ]
