AMORPHOUS CHOKE COILS
AMORPHOUS CHOKE COILS
?
Accessories used for choke coils of lying type
(mm)
(mm)
Pedestal (P/N XD4054HW)
Pedestal (P/N XD3237HW)
P/N of available core
P/N of available core
SIDE VIEW
G6
G7
G8
J7H
J8H
N6
N7
X6
G9
SIDE VIEW
JRH
JAH
N9
XR
44.2
47.5
48.8
54
34
37
X7
X8
123
BOTTOM VIEW
BOTTOM VIEW
Pitch between
adjacent lead
insertion holes:
22.1mm
1 2 3 4
5 6 7 8
9 10 11 12
12 - F1.5 drill hole
Pitch between
adjacent lead
insertion holes:
17.0mm
2 - F12 pin hole
456
Pitch between
adjacent lead
insertion holes:
22.1mm
Pitch between
adjacent lead
insertion holes:
17.0mm
2 - F1.2 pin hole
9 - F1.5 drill hole
789
2.5
Pitch between adjacent lead insertion holes : 2.5mm
Pitch between adjacent lead insertion holes : 2.5mm
(mm)
Pedestal (P/N XD4449HW)
(mm)
Pedestal (P/N XD5358HW)
P/N of available core
P/N of available core
G0
GQ
GJ
JBH
GK
SIDE VIEW
SIDE VIEW
JCH
JKH
WKH
54
58
46
49
BOTTOM VIEW
BOTTOM VIEW
21 - F1.5 drill hole
27 - F1.5 drill hole
1
8
2
3 4 5 6 7
1
2 3 4 5 6 7 8 9
Pitch between
adjacent lead
insertion holes:
23.0mm
Pitch between
4 - F1.2 pin hole
adjacent lead
insertion holes:
27.5mm
9 10 1112 13 14
101112131415161718
Pitch between
adjacent lead
insertion holes:
23.0mm
2 - F1.2 pin hole
Pitch between
adjacent lead
insertion holes:
27.5mm
15 16 17 18 19 20 21
192021222324252627
Pitch between adjacent lead insertion holes : 2.5mm
Pitch between adjacent lead insertion holes : 2.5mm
?Materials
Auxiliary pin material
P/N
Shape
Base material
Coil fixing material
XD1610VW, XD2212VW
XD2314VW, XD3415VW
XD4420VW, XD5625VW
XD3237HW, XD4054HW
XD4449HW, XD5358HW
PPS resin
F-type insulation
UL94V-0
Without auxiliary pin
or
Modified PA-6T
Polyamide resin
UL94V-0
Epoxy
adhensive
XD1610VW2, XD2212VW2
XD2314VW2, XD3415VW4
XD4420VW4, XD5625VW4
XD3237HW2, XD4054HW2
XD4449HW2, XD5358HW4
or
Fe or Fe-Ni alloy
Standard F0.8mm, F1.0mm, F1.2mm
Solder plating
Without auxiliary pin
PBT resin
B-type insulation
UL94V-0
?Note on use
@The auxiliay pins are normally insulated from lead wires.
@Contact NIPPON CHEMI-CON for the shape, dimension, and strength of the auxiliary pin.
@The specification described in this manual is defined on the basis of the documentation, information, and data obtained when the document is written. However, the
actual performance of each product may vary depending on the configuration of the circuit including the product. Therefore, confirm the performance and stability
of the product in the circuit which you design.
@In general, electronic components may generate heat depending on their operating conditions. Accordingly, never use the products near some flammable sub-
stances. In addition, never use the products if any specification exceeds the rated value. This may cause human injury and/or device failure.
(2/2)
CAT. No. E1008E