S/MON/SO848070/B/01/03/2005
okpac
page 3 / 6F/GB
Fig. 2 Courbes thermiques & Choix dissipateur thermique / Thermal curves and heatsink choice
140
140
130
120
110
100
90
0,3K/W
0,55K/W
130
120
110
100
90
0,75K/W
Full on State
0,95K/W
1,1K/W
1,5K/W
80
80
70
70
60
60
2,1K/W
50
50
40
40
30
30
50% on State
6K/W
20
20
10
10
0
0
0 10 20 30 40 50 60 70 80 90 100
0
10 20 30 40 50 60 70 80 90 100 110
Courant de charge / RMS load current (A)
Température ambiante / Ambient temperature (°C)
6K/W correspond à un relais monté sur un adaptateur DIN celduc type 1LD12020
6K/W corresponds to a relay mounted on a DIN rail adaptator like celduc 1LD12020
fig 3 : Courants de surcharges / Overload currents
1 -Itsm non répétitif sans tension réappliquée est
donné pour la détermination des protections.
1 - No repetitive Itsm is given without voltage
reapplied . This curve is used to define the
protection (fuses).
Fig.3 Surcharge de courant : Itsm (Apeak) = f(t) pour modéle 95A(Itsm=1500A)
Surge current : Itsm (Apeak) = f(t) for 95A models with Itsm =1500A
1500
1000
2 -Itsm répétitif est donné pour des surcharges de
courant (Tj initiale=70°C).
Surcharge de courant non répétitive sans tension réappliquée /
No repetive surge current without voltage reapplied.
Attention : la répétition de ces surcharges de courant
diminue la durée de vie du relais.
2 - Repetitive Itsm is given for inrush current with
initial Tj = 70°C. In normal operation , this curve
musn't be exceeded.
500
1
Surcharge de courant répétitive avec tension réappliquée
Repetive surge current with voltage reapplied.
2
0
0,01
0,1
1
10
t (s)
Be careful, the repetition of the surge current
decreases the life expectancy of the SSR.
−>
Attention ! les relais à semi-conducteurs ne procurent pas d'isolation galvanique entre le réseau et la charge. Ils doivent être utilisés
associés à un disjoncteur avec propriété de sectionnement ou similaire, afin d'assurer un sectionnement fiable en amont de la ligne dans
l'hypothèse d'une défaillance et pour tous les cas où le relais doit être isolé du réseau (maintenance ; non utilisation sur une longue durée...).
−>
Warning ! semiconductor relays don't provide any galvanic insulation between the load and the mains. Always use in conjunction
with an adapted circuit breaker with isolation feature or a similar device in order to ensure a reliable insulation in the event of wrong
function and when the relay must be insulated from the mains (maintenance ; if not used for a long duration ...).
celduc
www.celduc.com
r
e
l
a
i
s
Rue Ampère B.P. 4
42290 SORBIERS - FRANCE
E-Mail : celduc-relais@celduc.com
Fax +33 (0) 4 77 53 85 51
Service Commercial France Tél. : +33 (0) 4 77 53 90 20
Sales Dept.For Europe Tel. : +33 (0) 4 77 53 90 21 Sales Dept. Asia : Tél. +33 (0) 4 77 53 90 19