欢迎访问ic37.com |
会员登录 免费注册
发布采购

CAT1021PE-45TE13 参数 Datasheet PDF下载

CAT1021PE-45TE13图片预览
型号: CAT1021PE-45TE13
PDF下载: 下载PDF文件 查看货源
内容描述: 监控电路,带有I2C串行2K位CMOS EEPROM ,手动复位及看门狗定时器 [Supervisory Circuits with I2C Serial 2k-bit CMOS EEPROM, Manual Reset and Watchdog Timer]
分类和应用: 监控可编程只读存储器电动程控只读存储器电可擦编程只读存储器
文件页数/大小: 20 页 / 149 K
品牌: CATALYST [ CATALYST SEMICONDUCTOR ]
 浏览型号CAT1021PE-45TE13的Datasheet PDF文件第9页浏览型号CAT1021PE-45TE13的Datasheet PDF文件第10页浏览型号CAT1021PE-45TE13的Datasheet PDF文件第11页浏览型号CAT1021PE-45TE13的Datasheet PDF文件第12页浏览型号CAT1021PE-45TE13的Datasheet PDF文件第14页浏览型号CAT1021PE-45TE13的Datasheet PDF文件第15页浏览型号CAT1021PE-45TE13的Datasheet PDF文件第16页浏览型号CAT1021PE-45TE13的Datasheet PDF文件第17页  
CAT1021, CAT1022, CAT1023  
Immediate/Current Address Read  
Sequential Read  
The CAT1021/22/23 address counter contains the  
address of the last byte accessed, incremented by one.  
In other words, if the last READ or WRITE access was  
to address N, the READ immediately following would  
access data from address N + 1. For N = E = 255, the  
counter will wrap around to zero and continue to clock  
out valid data. After the CAT1021/22/23 receives its  
slave address information (with the R/W bit set to one),  
it issues an acknowledge, then transmits the 8-bit byte  
requested. The master device does not send an  
acknowledge, but will generate a STOP condition.  
The Sequential READ operation can be initiated by  
either the Immediate Address READ or Selective READ  
operations. After the CAT1021/22/23 sends the inital 8-  
bit byte requested, the Master will responds with an  
acknowledge which tells the device it requires more  
data.TheCAT1021/22/23willcontinuetooutputan8-bit  
byte for each acknowledge, thus sending the STOP  
condition.  
The data being transmitted from the CAT1021/22/23 is  
sent sequentially with the data from address N followed  
by data from address N + 1. The READ operation  
address counter increments all of the CAT1021/22/23  
addressbitssothattheentirememoryarraycanberead  
during one operation.  
Selective/Random Read  
Selective/Random READ operations allow the Master  
device to select at random any memory location for a  
READ operation. The Master device first performs a  
‘dummywriteoperationbysendingtheSTARTcondition,  
slave address and byte addresses of the location it  
wishestoread.AftertheCAT1021/22/23acknowledges,  
the Master device sends the START condition and the  
slaveaddressagain,thistimewiththeR/Wbitsettoone.  
TheCAT1021/22/23thenrespondswithitsacknowledge  
and sends the 8-bit byte requested. The master device  
does not send an acknowledge but will generate a  
STOP condition.  
Figure 11. Selective Read Timing  
S
T
A
R
T
S
T
A
R
T
S
T
O
P
BUS ACTIVITY:  
MASTER  
SLAVE  
ADDRESS  
BYTE  
ADDRESS (n)  
SLAVE  
ADDRESS  
SDA LINE  
S
S
P
A
C
K
A
C
K
A
C
K
N
O
DATA n  
A
C
K
Figure 12. Sequential Read Timing  
S
T
O
P
BUS ACTIVITY:  
MASTER  
SLAVE  
ADDRESS  
DATA n  
DATA n+1  
DATA n+2  
DATA n+x  
SDA LINE  
P
A
C
K
A
C
K
A
C
K
A
C
K
N
O
A
C
K
Doc No. 3009, Rev. K  
13