欢迎访问ic37.com |
会员登录 免费注册
发布采购

CDK1305CSO28_Q 参数 Datasheet PDF下载

CDK1305CSO28_Q图片预览
型号: CDK1305CSO28_Q
PDF下载: 下载PDF文件 查看货源
内容描述: 10位, 40 MSPS 175MW A / D转换器 [10-bit, 40 MSPS 175mW A/D Converter]
分类和应用: 转换器
文件页数/大小: 12 页 / 1804 K
品牌: CADEKA [ CADEKA MICROCIRCUITS LLC. ]
 浏览型号CDK1305CSO28_Q的Datasheet PDF文件第3页浏览型号CDK1305CSO28_Q的Datasheet PDF文件第4页浏览型号CDK1305CSO28_Q的Datasheet PDF文件第5页浏览型号CDK1305CSO28_Q的Datasheet PDF文件第6页浏览型号CDK1305CSO28_Q的Datasheet PDF文件第8页浏览型号CDK1305CSO28_Q的Datasheet PDF文件第9页浏览型号CDK1305CSO28_Q的Datasheet PDF文件第10页浏览型号CDK1305CSO28_Q的Datasheet PDF文件第11页  
Data Sheet
Specification Definitions
aperture Delay
Aperture delay represents the point in time, relative to
the rising edge of the CLOCK input, that the analog input
is sampled.
aperture Jitter
The variations in aperture delay for successive samples.
Differential Gain (DG)
A signal consisting of a sine wave superimposed on vari-
ous DC levels is applied to the input. Differential gain is
the maximum variation in the sampled sine wave ampli-
tudes at these DC levels.
Differential phase (Dp)
A signal consisting of a sine wave superimposed on vari-
ous DC levels is applied to the input. Differential phase is
the maximum variation in the sampled sine wave phases
at these DC levels.
effective number of Bits (enoB)
SINAD = 6.02N + 1.76, where N is equal to the effective
number of bits.
N = SINAD – 1.76
6.02
input Bandwidth
Small signal (50mV) bandwidth (3dB) of analog input stage.
Differential linearity error (Dle)
Error in the width of each code from its theoretical value.
(Theoretical = V
FS
/2
N
)
integral linearity error (ile)
Linearity error refers to the deviation of each individual
code (normalized) from a straight line drawn from –FS
through +FS. The deviation is measured from the edge of
each particular code to the true straight line.
output Delay
Time between the clock’s triggering edge and output data
valid.
overvoltage recovery time
The time required for the ADC to recover to full accuracy
after an analog input signal 125% of full scale is reduced
to 50% of the full-scale value.
signal-to-noise ratio (snr)
The ratio of the fundamental sinusoid power to the total
noise power. Harmonics are excluded.
signal-to-noise and Distortion (sinaD)
The ratio of the fundamental sinusoid power to the total
noise and distortion power.
total Harmonic Distortion (tHD)
The ratio of the total power of the first 9 harmonics to the
power of the measured sinusoidal signal.
spurious free Dynamic range (sfDr)
The ratio of the fundamental sinusoidal amplitude to the
single largest harmonic or spurious signal.
CDK1305
10-bit, 40 MSPS 175mW A/D Converter
REV 1A
Figure 1. Timing Diagram 1
©2008 CADEKA Microcircuits LLC
www.cadeka.com
7