ABSOLUTE MAXIMUM RATINGS(1)
ELECTROSTATIC
DISCHARGE SENSITIVITY
This integrated circuit can be damaged by ESD. Texas Instru-
ments recommends that all integrated circuits be handled with
appropriate precautions. Failure to observe proper handling
and installation procedures can cause damage.
+VS ....................................................................................................... +6V
Analog Input ........................................................... (–0.3V) to (+VS + 0.3V)
Logic Input ............................................................. (–0.3V) to (+VS + 0.3V)
Case Temperature ......................................................................... +100°C
Junction Temperature .................................................................... +150°C
Storage Temperature ..................................................................... +150°C
NOTE: (1) Stresses above those listed under “Absolute Maximum Ratings”
may cause permanent damage to the device. Exposure to absolute maximum
conditions for extended periods may affect device reliability.
ESD damage can range from subtle performance degradation
to complete device failure. Precision integrated circuits may be
more susceptible to damage because very small parametric
changes could cause the device not to meet its published
specifications.
PACKAGE/ORDERING INFORMATION
SPECIFIED
PACKAGE
DESIGNATOR(1)
TEMPERATURE
RANGE
PACKAGE
MARKING
ORDERING
NUMBER
TRANSPORT
MEDIA, QUANTITY
PRODUCT
PACKAGE-LEAD
ADS2807Y
TQFP-64
PAP
–40°C to +85°C
ADS2807Y
ADS2807Y/1K5
ADS2807Y/250
Tape and Reel, 1500
Tape and Reel, 250
"
"
"
"
"
NOTE: (1) For the most current specifications and package information, refer to our web site at www.ti.com.
ELECTRICAL CHARACTERISTICS
At TA = full specified temperature range, VS = +5V, differential input range = 2V to 3V for each input, sampling rate = 50MHz, unless otherwise noted.
ADS2807Y
PARAMETER
CONDITIONS
MIN
TYP
MAX
UNITS
RESOLUTION
12 Tested
Bits
SPECIFIED TEMPERATURE RANGE
Ambient Air
–40
+85
°C
ANALOG INPUT
2V Full-Scale Input Range (Differential)
2V Full-Scale Input Range (Single-Ended)
3V Full-Scale Input Range (Differential)
3V Full-Scale Input Range (Single-Ended)
Analog Input Bias Current
2Vp-p, INT or EXT Ref
2Vp-p, INT or EXT Ref
3Vp-p, INT or EXT Ref
3Vp-p, INT or EXT Ref
2
1.5
1.75
1
3
3.5
3.25
4
V
V
V
V
µA
1
Analog Input Bandwidth
270
MHz
MΩ || pF
Input Impedance
1.25 || 3
CONVERSION CHARACTERISTICS
Sample Rate
10k
50M
Samples/s
Data Latency
6
Clock Cycles
DYNAMIC CHARACTERISTICS
Differential Linearity Error (largest code error)
f = 1MHz
f = 10MHz
No Missing Codes
±0.6
±0.6
Tested
Tested
±3.5
±1.0
±1.0
LSB
LSB
fS = 40MHz
fS = 50MHz,TA = +25°C
fS = 40MHz, Full Temp
TA = +25°C
Integral Linearity Error, f = 1MHz
Spurious-Free Dynamic Range(1)
f = 1MHz (–1dBFS input)
f = 10MHz (–1dBFS input)
f = 20MHz (–1dBFS input)
2-Tone Intermodulation Distortion(3)
f = 12MHz and 13MHz (–7dBFS each tone)
±5.0
LSBs
72
70
70
dBFS(2)
dBFS
dBFS
60
60
–71.8
dBc
Signal-to-Noise Ratio (SNR)
f = 1MHz (–1dBFS input)
f = 10MHz (–1dBFS input)
f = 20MHz (–1dBFS input)
f = 1MHz (–1dBFS input)
f = 10MHz (–1dBFS input)
66
65
65
68
68
dBFS
dBFS
dBFS
dBFS
dBFS
3Vp-p
3Vp-p
ADS2807
2
SBAS169B
www.ti.com
BB [ BURR-BROWN CORPORATION ]
