SPECIFICATIONS (CONT)
ELECTRICAL
TCASE = +25°C, 900ns conversion time, ±VCC = ±15V, +VDD = +5V, and 6-minute warm-up in a normal convection environment unless otherwise noted.
ADC601JG
TYP
ADC601KG
TYP
PARAMETER
CONDITIONS
MIN
MAX
MIN
MAX
UNITS
POWER SUPPLY REQUIREMENTS
Supply Voltages: +VCC
+14.25
–14.25
+4.75
+15
–15
+5
5.4
–65
53
+15.75
–15.75
+5.25
7.0
–84.5
68.9
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
V
V
V
mA
mA
mA
W
–VCC
+VDD
Supply Currents: +ICC
–ICC
+IDD
Power Consumption
Thermal Resistance, θJC
Nominal ±VCC and +VDD
1.3
25
1.7
°C/W
TEMPERATURE RANGE(8)
Specification
Operating
0
–25
+70
+85
*
*
*
*
°C
°C
* Same specifications as for ADC601JG.
NOTES: (1) Over or under range on the analog input results in constant maximum or minimum digital output. (2) FSR = Full Scale Range. (3) Adjustable to zero.
(4) DynamictestsareperformedusingSHC804withADC601unlessotherwisespecified.Performancemayvarydependinguponchoiceofsample/hold. (5) SeeTypical
Performance Curves. (6) dBc = level referred to carrier input signal = 0dB; fC = input frequency; fS = sampling frequency. (7) IMD is referred to the larger of the two
input test signals. If referred to the peak envelope signal (≈0dB), the intermodulation products will be 6dB lower. For example, unit connected for ±10V has 20V FSR.
(8) Temperature ranges refer to case temperature. Thermal resistance was measured on a small (5" diameter) handwired circuit board; with the test device in a (zero
insertion force) socket. Thermal resistance will be lower if the ADC601 is soldered into the PC board, a ground plane is used directly underneath the package, multiple
PC board layers are used, or forced air cooling is employed. Use heat sinking if necessary to keep the case at specified and operating temperatures.
ORDERING INFORMATION
ABSOLUTE MAXIMUM RATINGS
±VCC ................................................................................................... ±18V
+VDD .................................................................................................... +7V
Digital Inputs ..................................................................................... +5.5V
Analog Inputs ...................................................................................... ±VCC
Comparator Input ............................................................... –3.7V to +0.7V
Case Temperature ......................................................................... +125°C
Junction Temperature .................................................................... +165°C
Storage Temperature ...................................................... –65°C to +150°C
ADC601
(
)
G
Basic Model Number
Performance Grade Code
J, K: 0°C to +70°C Case Temperature
Package Code
G: Ceramic DIP
Stresses above these ratings may permanently damage the device.
PACKAGE INFORMATION(1)
PACKAGE DRAWING
MODEL
PACKAGE
NUMBER
ADC601JG
ADC601KG
32-Pin Hermetic DIP
32-Pin Hermetic DIP
172–2
172–2
NOTE: (1) For detailed drawing and dimension table, please see end of data
sheet, or Appendix D of Burr-Brown IC Data Book.
The information provided herein is believed to be reliable; however, BURR-BROWN assumes no responsibility for inaccuracies or omissions. BURR-BROWN assumes
no responsibility for the use of this information, and all use of such information shall be entirely at the user's own risk. Prices and specifications are subject to change
without notice. No patent rights or licenses to any of the circuits described herein are implied or granted to any third party. BURR-BROWN does not authorize or warrant
any BURR-BROWN product for use in life support devices and/or systems.
®
3
ADC601
BB [ BURR-BROWN CORPORATION ]
