(1)
MGA-53589 Absolute Maximum Rating
(3)
Symbol
Vin
Vd
Parameter
Units
V
Absolute Maximum
Thermal Resistance
(V =5.0V) θ = 62.5°C/W
d
jc
Max input voltage
0.8
Notes:
Supply Voltage (Id=52mA)
Power Dissipation (2)
CW RF Input Power
V
5.5
1. Operation of this device is excess
of any of these limits may cause
permanent damage.
2. Source lead temperature is 25°C.
Derate 7.7mW/°C for TL > 125°C.
3. Thermal resistance measured
using150°CInfra-RedMicroscopy
Technique.
Pd
mW
dBm
°C
400
Pin
13
Tj
Junction Temperature
Storage Temperature
150
Tstg
°C
-65 to 150
MGA-53589 Electrical Specification
T = 25°C, Z = 50 , V = 5V, unless noted
C
o
d
Symbol
Id
Parameter and Test Condition
Current Drawn
Frequency
Units
Min.
Typ.
Max.
stdev(4)
N/A
mA
40
52
70
0.001
NF
Noise Figure
0.9GHz(1)
1.9GHz(1)
2.4GHz(1)
-
-
-
1.24
1.66
1.61
-
2
-
-
dB
0.02
-
Gain
OIP3
P1dB
PAE
Gain
0.9GHz(1)
1.9GHz(1)
2.4GHz(1)
-
14
18.2
15.8
15.3
-
17
-
-
dB
0.07
-
Output Third Order Intercept Point(2)
Output Power at 1dB Gain Compression
Power Added Efficiency at P1dB
Input Return Loss
0.9GHz(1)
1.9GHz(1)
2.4GHz(1)
-
34
-
36.8
37
37.2
-
-
-
-
dBm
dBm
%
0.66
-
0.9GHz(1)
1.9GHz(1)
2.4GHz(1)
-
18.6
18.2
17.6
-
-
16.5
-
20.5
-
0.12
-
0.9GHz(1)
1.9GHz(1)
2.4GHz(1)
-
-
-
24.7
27.3
22.7
-
-
-
-
0.21
-
IRL
0.9GHz(1)
1.9GHz(1)
2.4GHz(1)
-
-
-
13.6
14.4
11.6
-
-
-
-
dB
0.29
-
ORL
Output Return Loss
0.9GHz(1)
1.9GHz(1)
2.4GHz(1)
-
-
-
20.3
15.7
14.1
-
-
-
-
dB
0.31
-
ISO
Isolation
0.9GHz(1)
1.9GHz(1)
2.4GHz(1)
-
-
-
22.1
22.4
22.3
-
-
-
-
dB
0.09
-
Notes:
1. Measurements obtained from a test circuit described in Figure 34. Input and output matching components are tuned for consistent OIP3; while
keeping VSWR better than 2:1. Data obtained are minus board losses.
2. I) Output power level and frequency of two fundamental tones at 0.9GHz; F1 & F2 =-0.38dB; F1=0.905GHz and F2=0.915GHz
II) Output power level and frequency of two fundamental tones at 1.9GHz; F1 & F2 =5.49dB; F1=1.905GHz and F2=1.915GHz
III) Output power level and frequency of two fundamental tones at 2.4GHz; F1 & F2 =5dB; F1=2.405GHz and F2=2.415GHz
3. Standard deviation data are based on at least 500 pieces samples size taken from 2 wafer lots. Future wafers allocated to this product may have
nominal values anywhere between the upper and lower specification limits.
2
AVAGO [ AVAGO TECHNOLOGIES LIMITED ]
