欢迎访问ic37.com |
会员登录 免费注册
发布采购

HFBR-4593 参数 Datasheet PDF下载

HFBR-4593图片预览
型号: HFBR-4593
PDF下载: 下载PDF文件 查看货源
内容描述: 塑料光纤电缆和附件多功能连接电信交换系统 [Plastic Optical Fiber Cable and Accessories for Versatile Link Telecommunications switching systems]
分类和应用: 光纤电信电信交换系统
文件页数/大小: 10 页 / 267 K
品牌: AVAGO [ AVAGO TECHNOLOGIES LIMITED ]
 浏览型号HFBR-4593的Datasheet PDF文件第2页浏览型号HFBR-4593的Datasheet PDF文件第3页浏览型号HFBR-4593的Datasheet PDF文件第4页浏览型号HFBR-4593的Datasheet PDF文件第5页浏览型号HFBR-4593的Datasheet PDF文件第7页浏览型号HFBR-4593的Datasheet PDF文件第8页浏览型号HFBR-4593的Datasheet PDF文件第9页浏览型号HFBR-4593的Datasheet PDF文件第10页  
Step 4  
Placeꢀtheꢀflushꢀconnectorꢀandꢀpolishingꢀfixtureꢀonꢀtheꢀdullꢀ  
sideꢀofꢀtheꢀ3ꢀµmꢀpinkꢀlappingꢀfilmꢀandꢀcontinueꢀtoꢀpolishꢀ  
theꢀfiberꢀandꢀconnectorꢀforꢀapproximatelyꢀ25ꢀstrokes.Theꢀ  
fiberꢀendꢀshouldꢀbeꢀflat,ꢀsmoothꢀandꢀclean.  
Step 3  
Thisꢀcableꢀisꢀnowꢀreadyꢀforꢀuse.  
Anyꢀexcessꢀfiberꢀprotrudingꢀfromꢀtheꢀconnectorꢀendꢀmayꢀ  
beꢀcutꢀoff;ꢀhowever,ꢀtheꢀtrimmedꢀfiberꢀshouldꢀextendꢀatꢀ  
leastꢀ1.5ꢀmmꢀ(0.06ꢀin)ꢀfromꢀtheꢀconnectorꢀend.  
Note:Useofthepinklappinglmnepolishingstepresultsin  
approximately 2 dB improvement in coupling performance  
of either a transmitter­receiver link or a bulkhead/splice over  
a 600 grit polish alone. This fine polish is comparable to the  
Avago factory polish. The fine polishing step may be omitted  
where an extra 2 dB of optical power is not essential, as with  
shortlinklengths. Properpolishingofthetipoftheber/con­  
nector face results in a tip diameter between 2.5 mm (0.098  
in.) minimum and 3.2 mm (0.126 in.) maximum..  
Insertꢀtheꢀconnectorꢀfullyꢀintoꢀtheꢀpolishingꢀfixtureꢀwithꢀ  
theꢀ trimmedꢀ fiberꢀ protrudingꢀ fromꢀ theꢀ bottomꢀ ofꢀ theꢀ  
fixture.Thisꢀplasticꢀpolishingꢀfixtureꢀcanꢀbeꢀusedꢀtoꢀpolishꢀ  
twoꢀsimplexꢀconnectorsꢀorꢀsimplexꢀlatchingꢀconnectorsꢀ  
simultaneously,ꢀorꢀoneꢀduplexꢀconnector.  
Note: The four dots on the bottom of the polishing fixture  
are wear indicators. Replace the polishing fixture when any  
dot is no longer visible. Typically, the polishing fixture can  
be used 10 times; 10 duplex connectors or 20 simplex con­  
nectors, two at a time.  
HFBR-4593 Polishing Kit  
Place the 600 grit abrasive paper on a flat smooth surface,  
pressing down on the connector, polish the fiber and the  
connector using a figure eight pattern of strokes until the  
connector is flush with the bottom of the polishing fixture.  
Wipe the connector and fixture with a clean cloth or tissue.  
6