AUSTIN SEMICONDUCTOR, INC.
FLASH
AS8F2M32
Austin Semiconductor, Inc.
FIGURE 1: PIN ASSIGNMENT
2M x 32 FLASH
FLASH MEMORY MODULE
(Top View)
68 Lead CQFP
AVAILABLEAS MILITARY
SPECIFICATIONS
• Military Processing (MIL-STD-883C para 1.2.2)
• Temperature Range -55C to 125C
FEATURES
• Fast access times of 90ns, 120ns, and 150ns
• 5.0V 10ꢀ, single poꢁer supply operation
• Loꢁ poꢁer consumption(TYP): 4µA CMOS stand-by
* TYP ICC(active) <120mA for READ/WRITE
• 20 year DATA RETENTION
• Minimum 1,000,000 Program/Erase Cycles per sector
guaranteed
• 32 equal sectors of 64 Kbytes each
• Any combination of Sectors can be Erased
• Group Sector Protection
GENERAL DESCRIPTION
The Austin Semiconductor, Inc. AS8F2M32 is a 64 Mbit, 5.0 volt-
only Flash memory. This device is designed to be programmed in-
system ꢁith the standard system 5.0 volt VCC supply. TheAS8F2M32
offers an access time of 90ns, alloꢁing high-speed microprocessors to
operate ꢁithout ꢁait states. To eliminate bus contention, the device has
separate chip enable (CE\), ꢁrite enable (WE\) and output enable (OE\)
controls.
• Supports FULL Chip Erase
• Compatible ꢁith JEDEC standards
• Embedded Erase and Program Algorithms
• Data\ Polling and Toggle bits for detection of program or erase
cycle completion.
• Erase Suspend/Resume
• Hardꢁare Reset pin (RESET\)
• Built in Decoupling Caps and Multiple Ground Pins for Loꢁ Noise
Operation
• Separate Poꢁer and Ground Planes to improve noise immunity
The device requires only a single 5.0 volt poꢁer supply for both
read and ꢁrite functions. internally generated and regulated voltages
are provided for the program and erase operations.
The device is entirely command set compatible ꢁith the JEDEC
single-poꢁer-supply FLASH standard. Commands are ꢁritten to the
command register using standard microprocessor ꢁrite timings.
Register contents serve as input to an internal state-matching that
controls the erase and programming circuitry. Write cycles also
internally latch addresses and data needed for the programming and
erase operations. Reaching data out of the device is similar to reading
from other FLASH or EPROM devices.
OPTION
•Timing
90ns
MARKING
-90
-120
-150
120ns
150ns
Device programming occurs by executing the program command
sequence. This initiates the Embedded Program algorithm - an internal
algorithm that automatically time the program pulse ꢁidths and verifies
proper cell margin.
Device erasure occurs by executing the erase command sequence.
This initiates the Embedded Erase algorithm - an internal algorithm that
automatically preprograms the array (if it is not already programmed)
before executing the erase operation. During erase, the device
automatically times the erase pulse ꢁidths and verifies proper cell
margin.
The host system can detect ꢁhether a program or erase operation is
complete by observing the RY/BY\ pin, or by reading the DQ7 (DATA\
Polling) and DQ6 (toggle) status bits. After a program or erase cycle
has been completed, the device is ready to read array data or accept
another command.
• Packages
Ceramic Quad Flat Pack (0.88" sq)
- MAX height .140"
Q
- Stand-off Height .035" min
For more products and information
please visit our ꢁeb site at
www.austinsemiconductor.com
(continued on page 2)
Austin Semiconductor, Inc. reserves the right to change products or specifications without notice.
AS8F2M32
Rev. 2.5 05/09
1
AUSTIN [ AUSTIN SEMICONDUCTOR ]
