ATmega640/1280/1281/2560/2561
Address
Name
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Page
0x1A (0x3A)
0x19 (0x39)
0x18 (0x38)
0x17 (0x37)
0x16 (0x36)
0x15 (0x35)
0x14 (0x34)
0x13 (0x33)
0x12 (0x32)
0x11 (0x31)
0x10 (0x30)
0x0F (0x2F)
0x0E (0x2E)
0x0D (0x2D)
0x0C (0x2C)
0x0B (0x2B)
0x0A (0x2A)
0x09 (0x29)
0x08 (0x28)
0x07 (0x27)
0x06 (0x26)
0x05 (0x25)
0x04 (0x24)
0x03 (0x23)
0x02 (0x22)
0x01 (0x21)
0x00 (0x20)
TIFR5
TIFR4
TIFR3
TIFR2
TIFR1
TIFR0
PORTG
DDRG
PING
-
-
-
-
ICF5
ICF4
-
OCF5C
OCF4C
OCF3C
-
OCF5B
OCF4B
OCF3B
OCF2B
OCF1B
OCF0B
PORTG2
DDG2
OCF5A
OCF4A
OCF3A
OCF2A
OCF1A
OCF0A
PORTG1
DDG1
TOV5
TOV4
page 168
page 169
page 168
page 194
page 168
page 134
page 102
page 102
page 103
page 101
page 102
page 102
page 102
page 102
page 102
page 101
page 101
page 101
page 101
page 101
page 101
page 101
page 101
page 101
page 100
page 100
page 100
-
-
-
ICF3
-
TOV3
-
-
-
-
TOV2
-
-
ICF1
-
OCF1C
-
TOV1
-
-
-
-
TOV0
-
-
PORTG5
DDG5
PING5
PORTF5
DDF5
PORTG4
DDG4
PING4
PORTF4
DDF4
PINF4
PORTE4
DDE4
PINE4
PORTD4
DDD4
PIND4
PORTC4
DDC4
PINC4
PORTB4
DDB4
PINB4
PORTA4
DDA4
PINA4
PORTG3
DDG3
PING3
PORTF3
DDF3
PORTG0
DDG0
-
-
-
-
PING2
PORTF2
DDF2
PING1
PORTF1
DDF1
PING0
PORTF0
DDF0
PORTF
DDRF
PINF
PORTF7
DDF7
PINF7
PORTE7
DDE7
PINE7
PORTD7
DDD7
PIND7
PORTC7
DDC7
PINC7
PORTB7
DDB7
PINB7
PORTA7
DDA7
PINA7
PORTF6
DDF6
PINF6
PORTE6
DDE6
PINE6
PORTD6
DDD6
PIND6
PORTC6
DDC6
PINC6
PORTB6
DDB6
PINB6
PORTA6
DDA6
PINA6
PINF5
PORTE5
DDE5
PINE5
PORTD5
DDD5
PIND5
PORTC5
DDC5
PINC5
PORTB5
DDB5
PINB5
PORTA5
DDA5
PINA5
PINF3
PORTE3
DDE3
PINF2
PINF1
PINF0
PORTE0
DDE0
PORTE
DDRE
PINE
PORTE2
DDE2
PORTE1
DDE1
PINE3
PORTD3
DDD3
PINE2
PINE1
PINE0
PORTD0
DDD0
PORTD
DDRD
PIND
PORTD2
DDD2
PORTD1
DDD1
PIND3
PORTC3
DDC3
PIND2
PIND1
PIND0
PORTC0
DDC0
PORTC
DDRC
PINC
PORTC2
DDC2
PORTC1
DDC1
PINC3
PORTB3
DDB3
PINC2
PINC1
PINC0
PORTB0
DDB0
PORTB
DDRB
PINB
PORTB2
DDB2
PORTB1
DDB1
PINB3
PORTA3
DDA3
PINB2
PINB1
PINB0
PORTA0
DDA0
PORTA
DDRA
PINA
PORTA2
DDA2
PORTA1
DDA1
PINA3
PINA2
PINA1
PINA0
Notes: 1. For compatibility with future devices, reserved bits should be written to zero if accessed. Reserved I/O memory addresses
should never be written.
2. I/O registers within the address range $00 - $1F are directly bit-accessible using the SBI and CBI instructions. In these reg-
isters, the value of single bits can be checked by using the SBIS and SBIC instructions.
3. Some of the status flags are cleared by writing a logical one to them. Note that the CBI and SBI instructions will operate on
all bits in the I/O register, writing a one back into any flag read as set, thus clearing the flag. The CBI and SBI instructions
work with registers 0x00 to 0x1F only.
4. When using the I/O specific commands IN and OUT, the I/O addresses $00 - $3F must be used. When addressing I/O regis-
ters as data space using LD and ST instructions, $20 must be added to these addresses. The
ATmega640/1280/1281/2560/2561 is a complex microcontroller with more peripheral units than can be supported within
the 64 location reserved in Opcode for the IN and OUT instructions. For the Extended I/O space from $60 - $1FF in SRAM,
only the ST/STS/STD and LD/LDS/LDD instructions can be used.
15
2549LS–AVR–08/07
ATMEL [ ATMEL ]
