欢迎访问ic37.com |
会员登录 免费注册
发布采购

ATMEGA32L-8AUR 参数 Datasheet PDF下载

ATMEGA32L-8AUR图片预览
型号: ATMEGA32L-8AUR
PDF下载: 下载PDF文件 查看货源
内容描述: [RISC Microcontroller, 8-Bit, FLASH, AVR RISC CPU, 8MHz, CMOS, PQFP44, 10 X 10 MM, 1 MM HEIGHT, 0.80 MM PITCH, GREEN, PLASTIC, MS-026ACB, TQFP-44]
分类和应用: 闪存微控制器
文件页数/大小: 347 页 / 3171 K
品牌: ATMEL [ ATMEL ]
 浏览型号ATMEGA32L-8AUR的Datasheet PDF文件第191页浏览型号ATMEGA32L-8AUR的Datasheet PDF文件第192页浏览型号ATMEGA32L-8AUR的Datasheet PDF文件第193页浏览型号ATMEGA32L-8AUR的Datasheet PDF文件第194页浏览型号ATMEGA32L-8AUR的Datasheet PDF文件第196页浏览型号ATMEGA32L-8AUR的Datasheet PDF文件第197页浏览型号ATMEGA32L-8AUR的Datasheet PDF文件第198页浏览型号ATMEGA32L-8AUR的Datasheet PDF文件第199页  
ATmega32(L)  
Figure 93. Formats and States in the Slave Transmitter Mode  
Reception of the own  
slave address and one or  
more data bytes  
S
SLA  
R
A
DATA  
A
DATA  
A
P or S  
$A8  
A
$B8  
$C0  
Arbitration lost as master  
and addressed as slave  
$B0  
Last data byte transmitted.  
Switched to not addressed  
slave (TWEA = '0')  
A
All 1's  
P or S  
$C8  
Any number of data bytes  
and their associated acknowledge bits  
From master to slave  
From slave to master  
DATA  
A
This number (contained in TWSR) corresponds  
to a defined state of the Two-wire Serial Bus. The  
prescaler bits are zero or masked to zero  
n
Miscellaneous States  
There are two status codes that do not correspond to a defined TWI state, see Table 78.  
Status $F8 indicates that no relevant information is available because the TWINT Flag is  
not set. This occurs between other states, and when the TWI is not involved in a serial  
transfer.  
Status $00 indicates that a bus error has occurred during a Two-wire Serial Bus trans-  
fer. A bus error occurs when a START or STOP condition occurs at an illegal position in  
the format frame. Examples of such illegal positions are during the serial transfer of an  
address byte, a data byte, or an acknowledge bit. When a bus error occurs, TWINT is  
set. To recover from a bus error, the TWSTO Flag must set and TWINT must be cleared  
by writing a logic one to it. This causes the TWI to enter the not addressed slave mode  
and to clear the TWSTO Flag (no other bits in TWCR are affected). The SDA and SCL  
lines are released, and no STOP condition is transmitted.  
Table 78. Miscellaneous States  
Status Code  
(TWSR)  
Prescaler Bits  
are 0  
Application Software Response  
Status of the Two-wire Serial  
Bus and Two-wire Serial Inter-  
face Hardware  
To TWCR  
STO TWINT  
No TWCR action  
To/from TWDR  
STA  
0
TWEA  
X
Next Action Taken by TWI Hardware  
Wait or proceed current transfer  
$F8  
No relevant state information No TWDR action  
available; TWINT = “0”  
$00  
Bus error due to an illegal No TWDR action  
START or STOP condition  
1
1
Only the internal hardware is affected, no STOP condi-  
tion is sent on the bus. In all cases, the bus is released  
and TWSTO is cleared.  
195  
2503J–AVR–10/06  
 复制成功!