欢迎访问ic37.com |
会员登录 免费注册
发布采购

AT27C512R 参数 Datasheet PDF下载

AT27C512R图片预览
型号: AT27C512R
PDF下载: 下载PDF文件 查看货源
内容描述: 512K 64K ×8 OTP EPROM CMOS [512K 64K x 8 OTP CMOS EPROM]
分类和应用: 可编程只读存储器电动程控只读存储器
文件页数/大小: 9 页 / 252 K
品牌: ATMEL [ ATMEL ]
 浏览型号AT27C512R的Datasheet PDF文件第1页浏览型号AT27C512R的Datasheet PDF文件第2页浏览型号AT27C512R的Datasheet PDF文件第3页浏览型号AT27C512R的Datasheet PDF文件第4页浏览型号AT27C512R的Datasheet PDF文件第5页浏览型号AT27C512R的Datasheet PDF文件第6页浏览型号AT27C512R的Datasheet PDF文件第8页浏览型号AT27C512R的Datasheet PDF文件第9页  
AT27C512R  
AC Programming Characteristics  
RapidProgramming Algorithm  
TA = 25 ± 5°C, VCC = 6.5 ± 0.25V, OE/VPP = 13.0 ± 0.25V  
A 100 µs CE pulse width is used to program. The address  
is set to the first location. V  
is raised to 6.5V and  
CC  
Sym-  
bol  
Test  
Condtions*  
Limits  
Units  
OE/V is raised to 13.0V. Each address is first pro-  
PP  
(1)  
Parameter  
Min  
Max  
grammed with one 100 µs CE pulse without verification.  
Then a verification/reprogramming loop is executed for  
each address. In the event a byte fails to pass verification,  
up to 10 successive 100 µs pulses are applied with a veri-  
fication after each pulse. If the byte fails to verify after 10  
pulses have been applied, the part is considered failed.  
After the byte verifies properly, the next address is se-  
Address Setup Time  
OE/VPP Setup Time  
OE/VPP Hold Time  
Data Setup Time  
Address Hold Time  
Data Hold Time  
2
2
2
2
0
2
µs  
µs  
µs  
µs  
µs  
µs  
t
t
t
t
t
t
AS  
OES  
OEH  
DS  
AH  
lected until all have been checked. OE/V is then low-  
PP  
DH  
ered to V and V to 5.0V. All bytes are read again and  
IL  
CC  
CE High to  
compared with the original data to determine if the device  
passes or fails.  
0
130  
ns  
Output Float Delay (2)  
t
DFP  
VCC Setup Time  
2
µs  
µs  
µs  
µs  
t
t
t
t
VCS  
PW  
DV  
CE Program Pulse Width (3)  
Data Valid from CE (2)  
OE/VPP Recovery Time  
95  
105  
1
2
VR  
OE/VPP Pulse Rise  
Time During Programming  
50  
ns  
t
PRT  
*AC Conditions of Test:  
Input Rise and Fall Times (10% to 90%).............. 20 ns  
Input Pulse Levels....................................0.45V to 2.4V  
Input Timing Reference Level....................0.8V to 2.0V  
Output Timing Reference Level.................0.8V to 2.0V  
Notes: 1. VCC must be applied simultaneously or before  
OE/VPP and removed simultaneously or after  
OE/VPP  
.
2. This parameter is only sampled and is not 100%  
tested. Output Float is defined as the point where  
data is no longer driven — see timing diagram.  
3. Program Pulse width tolerance is 100 µsec ± 5%.  
Atmel’s 27C512R Integrated  
Product Identification Code  
Pins  
Hex  
Codes  
Data  
A0 O7 O6 O5 O4 O3 O2 O1 O0  
Manufacturer  
Device Type  
0
1
0
0
0
0
0
0
1
0
1
1
1
1
1
0
0
1
1E  
0D  
3-141