�½�½�½�½�½�½�½�½�½�½�½�½�½�½�½�½�½�½�½�½�½�½�½�½�½�½�½�½�½�½�½�½�½�½�½�½�½�½�½�½�½�½�½�½
�½�½�½�½
�½ �½ �½ �½ �½ �½ �½ �½ �½ �½ �½ �½ �½ �½ �½
�½�½�½�½�½�½�½�½�½�½�½�½�½�½�½�½�½�½�½�½�½�½�½�½�½�½�½�½�½�½�½�½�½�½�½�½�½�½�½�½�½�½�½�½�½�½�½�½�½�½�½�½�½�½�½�½�½�½�½�½�½�½
INTRODUCTION
This easy-to-use kit provides a platform for the evalua-
tion of the PB50 and PB58 high voltage power boosters.
The PB50 and PB58 are designed most commonly in
combination with a small signal, general purpose op
amp. However, they can also be used without a driver
amplifier. This kit can be used to analyze a multitude of
standard or proprietary circuit configurations.
�½�½
�½�½�½
�½�½�½
�½�½�½
�½�½�½
�½�½�½
�½�½�½
�½�½�½
�½�½�½�½
�½�½�½
�½�½�½
�½
�½�½�½�½�½�½
�½�½�½
PARTS LIST
Part #
HS13
EVAL01
MS03
HWRE02
HWRE05
TW0 3
Description
Heatsink
PC Board
Mating Socket
Hardware Kit
8-Pin Wire Wrap Socket
Thermal Washer
Quantity
1
1
1
1
1
1 Box/10
�½�½�½
�½�½�½
�½�½�½
�½�½�½�½
�½�½�½
�½�½�½
�½�½�½�½
�½�½�½�½
�½�½�½
�½�½�½
�½�½
�½�½�½
�½�½�½
�½�½�½
�½�½�½
�½�½�½
�½�½�½
�½�½�½
�½�½
HWRE02 contains the following:
4 #8 x .375" Panhead Screws
4 #8 x .375" Hex Spacers
4 #8 x 2.00" Hex Stand Offs
2 #6 x 1.25" Panhead Screws
2 #6 x 5/16" Hex Nuts
�½�½�½
�½�½�½
�½�½�½
�½�½�½
�½�½�½
�½�½�½
�½�½�½
�½�½�½
�½�½�½
�½�½�½
�½�½�½�½�½�½
�½�½�½�½�½
�½�½�½�½
�½�½
�½�½
�½�½�½
�½�½�½
�½�½
�½�½�½
�½�½�½
�½�½�½
�½�½�½�½�½
ASSEMBLY
�½�½�½�½�½�½�½�½�½�½�½�½�½�½�½�½�½�½�½�½�½�½�½�½
�½�½�½�½�½�½�½�½�½�½�½�½
�½�½�½�½�½�½�½�½�½�½�½�½�½�½�½�½�½�½�½�½�½�½
�½�½�½�½�½�½�½�½�½�½�½�½�½�½�½
�½�½�½�½�½�½�½�½�½�½�½�½�½
�½�½�½�½�½�½�½�½�½�½�½�½�½�½�½�½
�½�½�½�½�½�½�½�½
�½�½�½�½�½�½�½�½�½�½
�½�½�½�½�½�½�½�½�½�½�½
�½�½�½�½�½�½�½�½�½�½�½�½
�½�½�½�½�½�½�½�½�½�½�½�½�½�½�½�½�½�½
�½�½�½�½�½�½�½�½�½�½
�½�½�½�½�½�½�½�½�½�½�½�½
�½�½�½�½�½�½�½�½�½�½�½�½
�½�½�½�½�½�½�½�½�½�½�½�½�½
�½�½�½�½�½�½�½�½�½�½
�½�½�½�½�½�½�½�½�½�½�½
�½�½�½�½�½�½�½�½�½
�½�½�½�½�½�½�½
�½�½�½�½�½�½�½�½�½�½
�½�½�½�½�½�½�½�½�½�½�½�½�½�½
�½�½�½�½�½�½�½�½�½�½�½�½
�½�½�½�½�½�½�½�½�½�½�½�½�½
CAUTION
1. Use thermal grease or Apex Thermal Washer TW03 between power booster and heatsink.
2. Use 18 gauge teflon sleeve on at least two opposite pins
3. Mounting torque greater than 7 in•lbs on power booster mounting bolts will void warranty!
APEX MICROTECHNOLOGY CORPORATION • TELEPHONE (520) 690-8600 • FAX (520) 888-3329 • ORDERS (520) 690-8601 • EMAIL prodlit@apexmicrotech.com
1
APEX [ CIRRUS LOGIC ]
