欢迎访问ic37.com |
会员登录 免费注册
发布采购

AAT3192IJQ-2-T1 参数 Datasheet PDF下载

AAT3192IJQ-2-T1图片预览
型号: AAT3192IJQ-2-T1
PDF下载: 下载PDF文件 查看货源
内容描述: 2通道电荷泵LED驱动器 [2-Channel Charge-Pump LED Driver]
分类和应用: 驱动器
文件页数/大小: 18 页 / 572 K
品牌: ANALOGICTECH [ ADVANCED ANALOGIC TECHNOLOGIES ]
 浏览型号AAT3192IJQ-2-T1的Datasheet PDF文件第5页浏览型号AAT3192IJQ-2-T1的Datasheet PDF文件第6页浏览型号AAT3192IJQ-2-T1的Datasheet PDF文件第7页浏览型号AAT3192IJQ-2-T1的Datasheet PDF文件第8页浏览型号AAT3192IJQ-2-T1的Datasheet PDF文件第10页浏览型号AAT3192IJQ-2-T1的Datasheet PDF文件第11页浏览型号AAT3192IJQ-2-T1的Datasheet PDF文件第12页浏览型号AAT3192IJQ-2-T1的Datasheet PDF文件第13页  
PRODUCT DATASHEET  
AAT3192  
TM  
ChargePump  
2-Channel Charge-Pump LED Driver  
Functional Block Diagram  
C+ C-  
OUT  
Two-Mode  
CP Control  
IN  
D1  
D2  
2
VF Monitoring  
GND  
IREF  
S2Cwire Control  
(PWM Control)  
EN/SET  
(EN/PWM  
RSET  
DAC  
)
(RSET) to set the maximum LED current. The AAT3192  
can drive two constant output sinks (D1 and D2) with up  
to 30mA maximum current each. AnalogicTech’s S2Cwire  
serial interface enables the AAT3192-1/-2/-3 and chang-  
es the current sink magnitudes through the EN/SET pin.  
The AAT3192-4 uses an external PWM signal to enable  
the IC and control the brightness of the LEDs.  
Functional Description  
TheAAT3192isalow-costcharge-pumpsolutiondesigned  
to drive up to two white LEDs. The charge pump oper-  
ates from a 2.7V to 5.5V power source and converts it to  
voltage levels necessary to drive the LEDs. LED current  
is individually controlled through integrated current sinks  
powered from the output of the charge pump. Low 1x  
charge-pump output resistance and low-drop voltage  
current sinks allow the charge pump to stay in 1x mode  
with an input voltage as low as 3.75V and LED forward  
voltages as high as 3.5V. Once in 2x mode, the charge  
pump monitors the input supply voltage and automati-  
cally switches back to 1x mode when there is sufficient  
input voltage.  
Constant Current Control using RSET  
The maximum current is programmed by an external  
resistor at the RSET pin. Using a 14.3kΩ external resis-  
tor at the RSET pin, the AAT3192-1/-2/-4 includes an  
integrated serial LED current control that sets the full-  
scale LED current between 20mA and 0.63mA. For the  
AAT3192-3, a 11.5kΩ external resistor at the RSET pin  
sets the full-scale LED current between 20mA and  
1.3mA. The full-scale LED current can set higher or lower  
than 20mA; see Table 5. For maximum accuracy, a 1%  
tolerance resistor is recommended.  
The AAT3192 requires only four external components:  
one 1F ceramic capacitor for the charge pump flying  
capacitors (CP), one 1F ceramic input capacitor (CIN),  
one 1F ceramic output capacitor (COUT) and a resistor  
w w w . a n a l o g i c t e c h . c o m  
3192.2008.07.1.3  
9
 复制成功!