A29400 Series
in graphical form. See also the subsection on " I/O2:
Toggle Bit II".
RY/
: Read/
Busy
BY
The RY/
is a dedicated, open-drain output pin that
BY
I/O2: Toggle Bit II
indicates whether an Embedded algorithm is in progress
or complete. The RY/ status is valid after the rising
BY
pulse in the command sequence.
The "Toggle Bit II" on I/O2, when used with I/O6, indicates
whether a particular sector is actively erasing (that is, the
Embedded Erase algorithm is in progress), or whether that
sector is erase-suspended. Toggle Bit II is valid after the
edge of the final
WE
Since RY/
is an open-drain output, several RY/
BY
BY
pins can be tied together in parallel with a pull-up resistor
to VCC.
rising edge of the final
sequence.
pulse in the command
WE
If the output is low (Busy), the device is actively erasing or
programming. (This includes programming in the Erase
Suspend mode.) If the output is high (Ready), the device is
ready to read array data (including during the Erase
Suspend mode), or is in the standby mode.
I/O2 toggles when the system reads at addresses within
those sectors that have been selected for erasure. (The
system may use either
or
to control the read
CE
OE
cycles.) But I/O2 cannot distinguish whether the sector is
actively erasing or is erase-suspended. I/O6, by
comparison, indicates whether the device is actively
erasing, or is in Erase Suspend, but cannot distinguish
which sectors are selected for erasure. Thus, both status
bits are required for sector and mode information. Refer to
Table 6 to compare outputs for I/O2 and I/O6.
Table 6 shows the outputs for RY/
. Refer to “
RESET
BY
Timings”, “Timing Waveforms for Program Operation” and
“Timing Waveforms for Chip/Sector Erase Operation” for
more information.
I/O6: Toggle Bit I
Figure 5 shows the toggle bit algorithm in flowchart form,
and the section " I/O2: Toggle Bit II" explains the algorithm.
See also the " I/O6: Toggle Bit I" subsection. Refer to the
Toggle Bit Timings figure for the toggle bit timing diagram.
The I/O2 vs. I/O6 figure shows the differences between I/O2
and I/O6 in graphical form.
Toggle Bit I on I/O6 indicates whether an Embedded
Program or Erase algorithm is in progress or complete, or
whether the device has entered the Erase Suspend mode.
Toggle Bit I may be read at any address, and is valid after
the rising edge of the final
pulse in the command
WE
sequence (prior to the program or erase operation), and
during the sector erase time-out.
Reading Toggle Bits I/O6, I/O2
During an Embedded Program or Erase algorithm
operation, successive read cycles to any address cause
Refer to Figure 5 for the following discussion. Whenever
the system initially begins reading toggle bit status, it must
read I/O7 - I/O0 at least twice in a row to determine
whether a toggle bit is toggling. Typically, a system would
note and store the value of the toggle bit after the first
read. After the second read, the system would compare
the new value of the toggle bit with the first. If the toggle
bit is not toggling, the device has completed the program
or erase operation. The system can read array data on
I/O7 - I/O0 on the following read cycle.
However, if after the initial two read cycles, the system
determines that the toggle bit is still toggling, the system
also should note whether the value of I/O5 is high (see the
section on I/O5). If it is, the system should then determine
again whether the toggle bit is toggling, since the toggle bit
may have stopped toggling just as I/O5 went high. If the
toggle bit is no longer toggling, the device has successfully
completed the program or erase operation. If it is still
toggling, the device did not complete the operation
successfully, and the system must write the reset
command to return to reading array data.
The remaining scenario is that the system initially
determines that the toggle bit is toggling and I/O5 has not
gone high. The system may continue to monitor the toggle
bit and I/O5 through successive read cycles, determining
the status as described in the previous paragraph.
Alternatively, it may choose to perform other system tasks.
In this case, the system must start at the beginning of the
algorithm when it returns to determine the status of the
operation (top of Figure 5).
I/O6 to toggle. (The system may use either
or
to
CE
OE
control the read cycles.) When the operation is complete,
I/O6 stops toggling.
After an erase command sequence is written, if all sectors
selected for erasing are protected, I/O6 toggles for
approximately 100ms, then returns to reading array data. If
not all selected sectors are protected, the Embedded
Erase algorithm erases the unprotected sectors, and
ignores the selected sectors that are protected.
The system can use I/O6 and I/O2 together to determine
whether a sector is actively erasing or is erase-suspended.
When the device is actively erasing (that is, the Embedded
Erase algorithm is in progress), I/O6 toggles. When the
device enters the Erase Suspend mode, I/O6 stops
toggling. However, the system must also use I/O2 to
determine which sectors are erasing or erase-suspended.
Alternatively, the system can use I/O7 (see the subsection
on " I/O7 :
Polling").
Data
If a program address falls within a protected sector, I/O6
toggles for approximately 2ms after the program command
sequence is written, then returns to reading array data.
I/O6 also toggles during the erase-suspend-program
mode, and stops toggling once the Embedded Program
algorithm is complete.
The Write Operation Status table shows the outputs for
Toggle Bit I on I/O6. Refer to Figure 5 for the toggle bit
algorithm, and to the Toggle Bit Timings figure in the "AC
Characteristics" section for the timing diagram. The I/O2
vs. I/O6 figure shows the differences between I/O2 and I/O6
PRELIMINARY
(February, 2001, Version 0.1)
14
AMIC Technology, Inc.
AMICC [ AMIC TECHNOLOGY ]
