A29002/A290021 Series
Table 2. A29002/A290021 Top Boot Block Sector Address Table
Sector
A17
A16
A15
A14
A13
Sector Size
(Kbytes)
Address Range
SA0
SA1
SA2
SA3
SA4
SA5
SA6
0
0
1
1
1
1
1
0
1
0
1
1
1
1
X
X
X
0
1
1
1
X
X
X
X
0
X
X
X
X
0
64
64
64
32
8
00000h - 0FFFFh
10000h - 1FFFFh
20000h - 2FFFFh
30000h - 37FFFh
38000h - 39FFFh
3A000h - 3BFFFh
3C000h - 3FFFFh
0
1
8
1
X
16
Table 3. A29002/A290021 Bottom Boot Block Sector Address Table
Sector
A17
A16
A15
A14
A13
Sector Size
(Kbytes)
Address Range
SA0
SA1
SA2
SA3
SA4
SA5
SA6
0
0
0
0
0
1
1
0
0
0
0
1
0
1
0
0
0
1
X
X
X
0
1
X
0
16
8
00000h - 03FFFh
04000h - 05FFFh
06000h - 07FFFh
08000h - 0FFFFh
10000h - 1FFFFh
20000h - 2FFFFh
30000h - 3FFFFh
1
1
8
X
X
X
X
X
X
X
X
32
64
64
64
Codes (High Voltage Method) table. In addition, when
verifying sector protection, the sector address must appear
on the appropriate highest order address bits. Refer to the
corresponding Sector Address Tables. The Command
Definitions table shows the remaining address bits that are
don't care. When all necessary bits have been set as
required, the programming equipment may then read the
corresponding identifier code on I/O7 - I/O0.To access the
autoselect codes in-system, the host system can issue the
autoselect command via the command register, as shown
in the Command Definitions table. This method does not
require VID. See "Command Definitions" for details on
using the autoselect mode.
Autoselect Mode
The autoselect mode provides manufacturer and device
identification, and sector protection verification, through
identifier codes output on I/O7 - I/O0. This mode is primarily
intended for programming equipment to automatically
match a device to be programmed with its corresponding
programming algorithm. However, the autoselect codes
can also be accessed in-system through the command
register.
When using programming equipment, the autoselect mode
requires VID (11.5V to 12.5 V) on address pinA9. Address
pins A6, A1, and AO must be as shown in Autoselect
Table 4. A29002/A290021 Autoselect Codes (High Voltage Method)
Identifier Code on
I/O7 - I/O0
Description
A17 - A13 A12 - A10 A9
A8 - A7 A6 A5 - A2 A1
AO
Manufacturer ID: AMIC
X
X
X
X
VID
VID
X
X
VIL
VIL
X
X
VIL
VIL
VIL
VIH
37h
Device ID: A29002/
A290021
Top Boot Block: 8Ch
Bottom Boot Block: 0Dh
01h (protected)
Sector Protection
Verification
Sector
Address
X
VID
X
VIL
VIL
X
X
VIH
VIH
VIL
VIH
00h (unprotected)
7Fh
Continuation ID
X
X
VID
X
Note:
=VIL,
=VIL and
=VIH when Autoselect Mode
WE
CE
OE
(February, 2002, Version 1.0)
6
AMIC Technology, Inc.
AMICC [ AMIC TECHNOLOGY ]
