A27020 Series
Functional Description
Read Mode
The auto identify mode allows the reading out of a binary
code from a EPROM that will identify its manufacturer and
type. This mode is intended for use by programming
equipment for the purpose of automatically matching the
device to be programmed with its corresponding
programming algorithm.
The A27020 has two control functions, both of which must
be logically active in order to obtain data at the outputs.
CE is the power control and should be used for device
selection. OE is the output control and should be used to
data to the output pins, which is independent of device
selection. Assuming that addresses are stable, address
To activate the mode, the programming equipment must
apply 12.0V ± 0.5V on address line A9 of the A27020.
Three identification code can be read from data output pin
by toggling A0 and A1. The other addresses must be held
at VIL during this mode. Byte 0 (with A0 at VIL, A1 at VIL)
represents the manufacturer code which is 37H. Byte 1
and Byte 2 represent the device code and continuation
code, which is 64H and 7FH respectively. All identifiers for
these codes will possess odd parity, with MSB (IO7)
defined the parity bit.
access time (tAA) is equal to the delay from CE to output
(tCE). Data is available at the output after a delay (tOE) from
the falling edge of OE , as long as CE has been low and
the addresses have been stable for at least tACC - tOE.
Standby Mode
The A27020 has a standby mode which reduces the
active current from 30mA to 100mA. The A27020 is placed
in the standby mode by applying a CMOS high signal to
CE . When in the standby mode, the output are in a high
impedance state, independent of the OE .
Auto Identify Mode
Absolute Maximum Ratings*
*Comments
Stresses above those listed under "Absolute Maximum
Ratings" may cause permanent damage to this device.
These are stress ratings only. Functional operation of this
device at these or any other conditions above those
indicated in the operational sections of this specification
is not implied or intended. Exposure to the absolute
maximum rating conditions for extended periods may
affect device reliability.
Ambient Operating Temperature (TA) . . . . -10°C to +85°C
Storage Temperature Plastic Package (TSTG) . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -55°C to 125°C
Applied Input Voltage (VI):
All Pins Except A9, VPP and VCC . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . -0.6V to VCC + 0.6V
A9, VPP . . . . . . . . . . . . . . . . . . . . . . . . -0.6V to 13.5V
VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.6V to 7.0V
Output Voltage (VO) . . . . . . . . . . . . -0.6V to 7.0V (Note 1)
Notes:
1. During voltage transitions, the input may undershoot GND to -2.0V for periods less than 20 ns. Maximum DC voltage on
input and I/O may overshoot to VCC + 2.0V for periods less than 20 ns.
2. When transitions, A9 and VPP may undershoot GND to -2.0V for periods less than 20 ns. Maximum DC input voltage
on A9 and VPP is +13.5V which may overshoot to 14.0V for period less than 20 ns.
PRELIMINARY
(August, 2002, Version 0.0)
3
AMIC Technology, Inc.
AMICC [ AMIC TECHNOLOGY ]
