P R E L I M I N A R Y
Autoselect Mode
Sector/
Sector Block Size
Sector
A20–A12
111111100
111111101
111111110
111111111
The autoselect mode provides manufacturer and de-
vice identification, and sector protection verification,
through identifier codes output on DQ7–DQ0. This
mode is primarily intended for programming equip-
ment to automatically match a device to be
programmed with its corresponding programming al-
gorithm. However, the autoselect codes can also be
accessed in-system through the command register.
SA67
SA68
SA69
SA70
8 Kbytes
8 Kbytes
8 Kbytes
8 Kbytes
Table 11. Top Boot Sector/Sector Block
Addresses for Protection/Unprotection
To access the autoselect codes in-system, the host
system can issue the autoselect command via the
command register, as shown in Tables 16 and 18. This
method does not require VID. Refer to the Autoselect
Command Sequence section for more information.
Sector/Sector Block
Sector
A20–A12
Size
SA70
111111XXX
64 Kbytes
111110XXX,
111101XXX,
111100XXX
SA69-SA67
192 (3x64) Kbytes
Sector/Sector Block Protection and
Unprotection
(Note: For the following discussion, the term “sector”
applies to both sectors and sector blocks. A sector
block consists of two or more adjacent sectors that are
protected or unprotected at the same time (see Table
10).
SA66-SA63
SA62-SA59
SA58-SA55
SA54-SA51
SA50-SA47
SA46-SA43
SA42-SA39
SA38-SA35
SA34-SA31
SA30-SA27
SA26-SA23
SA22–SA19
SA18-SA15
SA14-SA11
1110XXXXX
1101XXXXX
1100XXXXX
1011XXXXX
1010XXXXX
1001XXXXX
1000XXXXX
0111XXXXX
0110XXXXX
0101XXXXX
0100XXXXX
0011XXXXX
0010XXXXX
0001XXXXX
256 (4x64) Kbytes
256 (4x64) Kbytes
256 (4x64) Kbytes
256 (4x64) Kbytes
256 (4x64) Kbytes
256 (4x64) Kbytes
256 (4x64) Kbytes
256 (4x64) Kbytes
256 (4x64) Kbytes
256 (4x64) Kbytes
256 (4x64) Kbytes
256 (4x64) Kbytes
256 (4x64) Kbytes
256 (4x64) Kbytes
Table 10. Top Boot Sector/Sector Block
Addresses for Protection/Unprotection
Sector/
Sector
A20–A12
Sector Block Size
SA0
000000XXX
64 Kbytes
000001XXX,
000010XXX
000011XXX
SA1–SA3
192 (3x64) Kbytes
000011XXX,
000010XXX,
000001XXX
SA4–SA7
SA8–SA11
0001XXXXX
0010XXXXX
0011XXXXX
0100XXXXX
0101XXXXX
0110XXXXX
0111XXXXX
1000XXXXX
1001XXXXX
1010XXXXX
1011XXXXX
1100XXXXX
1101XXXXX
1110XXXXX
256 (4x64) Kbytes
256 (4x64) Kbytes
256 (4x64) Kbytes
256 (4x64) Kbytes
256 (4x64) Kbytes
256 (4x64) Kbytes
256 (4x64) Kbytes
256 (4x64) Kbytes
256 (4x64) Kbytes
256 (4x64) Kbytes
256 (4x64) Kbytes
256 (4x64) Kbytes
256 (4x64) Kbytes
256 (4x64) Kbytes
SA10-SA8
192 (3x64) Kbytes
SA12–SA15
SA16–SA19
SA20–SA23
SA24–SA27
SA28–SA31
SA32–SA35
SA36–SA39
SA40–SA43
SA44–SA47
SA48–SA51
SA52–SA55
SA56–SA59
SA7
SA6
SA5
SA4
SA3
SA2
SA1
SA0
000000111
000000110
000000101
000000100
000000011
000000010
000000001
000000000
8 Kbytes
8 Kbytes
8 Kbytes
8 Kbytes
8 Kbytes
8 Kbytes
8 Kbytes
8 Kbytes
The hardware sector protection feature disables both
program and erase operations in any sector. The hard-
ware sector unprotection feature re-enables both
program and erase operations in previously protected
sectors. Note that the sector unprotect algorithm un-
protects all sectors in parallel. All previously protected
sectors must be individually re-protected. To change
data in protected sectors efficiently, the temporary
sector un protect function is available. See “Temporary
Sector/Sector Block Unprotect”.
111100XXX,
111101XXX,
111110XXX
SA60–SA62
192 (4x64) Kbytes
SA63
SA64
SA65
SA66
111111000
111111001
111111010
111111011
8 Kbytes
8 Kbytes
8 Kbytes
8 Kbytes
September 5, 2002
Am41DL32x8G
21
AMD [ AMD ]
