P R E L I M I N A R Y
the functionality of the device is guaranteed.
ABSOLUTE MAXIMUM RATINGS
Storage temperature
Am186EM/Am188EM Microcontrollers
Am186EM/Am188EM ..................... –65°C to +125°C
Am186EMLV/Am188EMLV.............–65°C to +125°C
Commercial (TC) .................................0°C to +100°C
Industrial* (TA)...................................–40°C to +85°C
VCC up to 33 MHz..................................... 5 V ± 10%
VCC greater than 33 MHz............................ 5 V ± 5%
Voltage on any pin with respect to ground
Am186/188EM ...........................–0.5 V to Vcc +0.5 V
Am186/188EMLV.......................–0.5 V to Vcc +0.5 V
Am186EMLV/Am188EMLV Microcontrollers
Commercial (TA) ...................................0°C to +70°C
VCC up to 25 MHz................................. 3.3 V ± 0.3 V
Note: Stresses above those listed under Absolute
Maximum Ratings may cause permanent device failure.
Functionality at or above these limits is not implied. Ex-
posure to absolute maximum ratings for extended peri-
ods may affect device reliability.
Where: TC = case temperature
TA = ambient temperature
*Industrial versions of Am186EM and Am188EM microcontrol-
lers are available in 20 and 25 MHz operating frequencies
only.
OPERATING RANGES
Operating Ranges define those limits between which
DC CHARACTERISTICS OVER COMMERCIAL OPERATING RANGE
Preliminary
Symbol
VIL
Parameter Description
Input Low Voltage (Except X1)
Clock Input Low Voltage (X1)
Input High Voltage (Except RES and X1)
Input High Voltage (RES)
Test Conditions
Min
Max
0.8
Unit
V
–0.5
–0.5
VIL1
0.8
V
VIH
2.0
VCC + 0.5
VCC + 0.5
VCC + 0.5
V
VIH1
VIH2
2.4
V
Clock Input High Voltage (X1)
Output Low Voltage
VCC – 0.8
V
Am186EM and Am188EM
IOL= 2.5 mA (S2–S0)
0.45
0.45
V
V
IOL= 2.0 mA (others)
VOL
Am186EMLV and Am188EMLV
IOL= 1.5 mA (S2–S0)
IOL= 1.0 mA (others)
Output High Voltage(a)
Am186EM and Am188EM
IOH= –2.4 mA @ 2.4 V
2.4
VCC +0.5
VCC
V
V
V
VOH
IOH= –200 µA @ VCC –0.5
IOH= –200 µA @ VCC –0.5
VCC –0.5
VCC –0.5
Am186EMLV and Am188EMLV
VCC
Power Supply Current @ 0°C
Am186EM and Am188EM
VCC = 5.5 V (b)
VCC = 3.6 V (b)
5.9
mA/
ICC
MHz
Am186EMLV and Am188EMLV
2.75
mA/
MHz
IOL = 2.5 mA (S2–S0)
IOL = 2.0 mA (others)
VOL
Output Low Voltage
0.45
V
ILI
Input Leakage Current @ 0.5 MHz
0.45 V ≤ VIN ≤ VCC
±10
±10
0.45
µA
µA
V
(d)
ILO
Output Leakage Current @ 0.5 MHz
0.45 V ≤ VOUT ≤ VCC
VCLO Clock Output Low
VCHO Clock Output High
ICLO = 4.0 mA
ICHO = –500 µA
VCC – 0.5
V
Notes:
a
The LCS/ONCE0, MCS3–MCS0, UCS/ONCE1, and RD pins have weak internal pullup resistors. Loading the LCS/ONCE0 and
UCS/ONCE1 pins in excess of IOH= –200 µA during reset can cause the device to go into ONCE mode.
b
c
Current is measured with the device in RESET with X1 and X2 driven, and all other non-power pins open but held High or Low.
Power supply current for the Am186EMLV and Am188EMLV microcontrollers, which are available in 20 and 25 MHz
operating frequencies only.
d
Testing is performed with the pins floating, either during HOLD or by invoking the ONCE mode.
Am186/188EM and Am186/188EMLV Microcontrollers
51