欢迎访问ic37.com |
会员登录 免费注册
发布采购

PPC440EPX-SPAFFFTS 参数 Datasheet PDF下载

PPC440EPX-SPAFFFTS图片预览
型号: PPC440EPX-SPAFFFTS
PDF下载: 下载PDF文件 查看货源
内容描述: 440EPx的PowerPC嵌入式处理器 [PowerPC 440EPx Embedded Processor]
分类和应用: PC
文件页数/大小: 94 页 / 3193 K
品牌: AMCC [ APPLIED MICRO CIRCUITS CORPORATION ]
 浏览型号PPC440EPX-SPAFFFTS的Datasheet PDF文件第51页浏览型号PPC440EPX-SPAFFFTS的Datasheet PDF文件第52页浏览型号PPC440EPX-SPAFFFTS的Datasheet PDF文件第53页浏览型号PPC440EPX-SPAFFFTS的Datasheet PDF文件第54页浏览型号PPC440EPX-SPAFFFTS的Datasheet PDF文件第56页浏览型号PPC440EPX-SPAFFFTS的Datasheet PDF文件第57页浏览型号PPC440EPX-SPAFFFTS的Datasheet PDF文件第58页浏览型号PPC440EPX-SPAFFFTS的Datasheet PDF文件第59页  
Revision 1.26 – October 15, 2007  
440EPx – PPC440EPx Embedded Processor  
Preliminary Data Sheet  
Signal Descriptions  
The PPC440EPx embedded controller is packaged in a 680-ball thermally enhanced plastic ball grid array  
(TE-PBGA). The following tables describe the package level pin-out.  
Table 7. Pin Summary  
Group  
Total Signal Pins  
AVDD  
No. of Pins  
367  
1
AGND  
EAVDD  
1
1
EAGND  
UAVDD  
1
4
UAGND  
OVDD  
5
26  
14  
12  
SOVDD  
EOVDD  
VDD  
56  
192  
313  
0
GND  
Total Power Pins  
Reserved  
Total Pins  
680  
In the table Table 8 on page 57, each I/O signal is listed along with a short description of its function. Active-low  
signals (for example, RAS) are marked with an overline. Please see Table 5 on page 21 for the pin (ball) number to  
which each signal is assigned.  
Multiplexed Signals  
Some signals are multiplexed on the same pin so that the pin can be used for different functions. In most cases,  
the signal names shown in this table are not accompanied by signal names that may be multiplexed on the same  
pin. If you need to know what, if any, signals are multiplexed with a particular signal, look up the name in Table 5  
on page 21. It is expected that in any single application a particular pin will always be programmed to serve the  
same function. The flexibility of multiplexing allows a single chip to offer a richer pin selection than would otherwise  
be possible.  
Note: Signals multiplexed with GPIO default to GPIO receivers and float after reset. Initialization software must  
configure the GPIO registers for the desired function as described in the GPIO chapter of the user’s manual. Any of  
these signals requiring a particular state prior to running initialization code must be terminated with pull ups or pull  
downs.  
Multipurpose Signals  
In addition to multiplexing, some pins are also multi-purpose. For example, the EBC peripheral controller address  
pins (PerAddr) are used as outputs by the PPC440EPx to broadcast an address to external slave devices when the  
PPC440EPx has control of the external bus. When, during normal operation, an external master gains ownership  
AMCC Proprietary  
55