Revision 1.15 – August 30, 2007
440GX – Power PC 440GX Embedded Processor
Data Sheet
Signal Functional Description (Sheet 1 of 8)
Notes:
1. Receiver input has hysteresis
2. Must pull up (recommended value is 3kΩ to 3.3V)
3. Must pull down (recommended value is 1kΩ)
4. If not used, must pull up (recommended value is 3kΩ to 3.3V)
5. If not used, must pull down (recommended value is 1kΩ)
6. Strapping input during reset; pull-up or pull-down required
Signal Name
PCI-X Interface
Description
I/O
Type
Notes
PCIXAD00:63
PCIXC0:7[BE0:7]
PCIXCap
Address/Data bus (bidirectional).
I/O
I/O
I
3.3V PCI
3.3V PCI
PCI-X Command[Byte Enables].
Capable of PCI-X operation.
3.3V LVTTL
3.3V PCI
5
PCIX133Cap
PCI-X devices are 133 MHz capable.
Provides timing to the PCI interface for PCI transactions.
O
PCIXClk
I
3.3V PCI
Note:If the PCI-X interface is not being used, drive this pin with a
3.3V clock signal at a frequency between 1 and 66MHz
Indicates the driving device has decoded its address as the target
of the current access.
PCIXDevSel
PCIXFrame
I/O
I/O
3.3V PCI
3.3V PCI
4
4
Driven by the current master to indicate beginning and duration of
an access.
Indicates that the specified agent is granted access to the bus.
When using an external PCI/PCI-X arbiter, connect the external
arbiter's Grant line to this signal.
PCIXGnt0
I/O
3.3V PCI
4
4
PCIXGnt1
Indicates that the specified agent is granted access to the bus.
Indicates that the specified agent is granted access to the bus.
I/O
O
3.3V PCI
3.3V PCI
PCIXGnt2:5
Used as a chip select during configuration read and write
transactions.
PCIXIDSel
PCIXINT
I
3.3V PCI
3.3V PCI
3.3V PCI
5
Level sensitive PCI interrupt.
O
Indicates initiating agent’s ability to complete the current data
phase of the transaction.
PCIXIRDY
I/O
4
5
3.3V LVTTL
w/pull-up
PCIXM66En
Capable of 66MHz operation.
I
PCIXParHigh
PCIXParLow
Even parity across PCIAD32:63 and PCIXC0:3[BE4:7].
Even parity across PCIAD0:31 and PCIXC0:3[BE0:3].
I/O
I/O
3.3V PCI
3.3V PCI
Reports data parity errors during all PCI transactions except a
Special Cycle.
PCIXPErr
I/O
I/O
I
3.3V PCI
3.3V PCI
3.3V PCI
4
4
4
An indication to the PCI-X arbiter that the specified agent wishes
to use the bus. When using an external PCI/PCI-X arbiter, connect
the external arbiter's Request line to this signal.
PCIXReq0
PCIXReq1:5
An indication to the PCI-X arbiter that the specified agent wishes
to use the bus.
PCIXReq64
PCIXAck64
PCIXReset
Asserted by the current bus master, indicating a 64-bit transfer.
Indicates the target can transfer data using 64 bits.
I/O
I/O
O
3.3V PCI
3.3V PCI
3.3V PCI
4
4
Brings PCI device registers and logic to a consistent state.
Reports address parity errors, data parity errors on the Special
Cycle command, or other catastrophic system errors.
PCIXSErr
PCIXStop
I/O
I/O
3.3V PCI
3.3V PCI
4
4
Indicates the current target is requesting the master to stop the
current transaction.
50
AMCC