欢迎访问ic37.com |
会员登录 免费注册
发布采购

PPC405GPR-3KB400Z 参数 Datasheet PDF下载

PPC405GPR-3KB400Z图片预览
型号: PPC405GPR-3KB400Z
PDF下载: 下载PDF文件 查看货源
内容描述: Power PC的405GPr嵌入式处理器 [Power PC 405GPr Embedded Processor]
分类和应用: PC
文件页数/大小: 57 页 / 1081 K
品牌: AMCC [ APPLIED MICRO CIRCUITS CORPORATION ]
 浏览型号PPC405GPR-3KB400Z的Datasheet PDF文件第25页浏览型号PPC405GPR-3KB400Z的Datasheet PDF文件第26页浏览型号PPC405GPR-3KB400Z的Datasheet PDF文件第27页浏览型号PPC405GPR-3KB400Z的Datasheet PDF文件第28页浏览型号PPC405GPR-3KB400Z的Datasheet PDF文件第30页浏览型号PPC405GPR-3KB400Z的Datasheet PDF文件第31页浏览型号PPC405GPR-3KB400Z的Datasheet PDF文件第32页浏览型号PPC405GPR-3KB400Z的Datasheet PDF文件第33页  
Revision 2.04 – September 7, 2007  
405GPr – Power PC 405GPr Embedded Processor  
Data Sheet  
Pull-Up and Pull-Down Resistors  
Pull-up and pull-down resistors are used for strapping during reset and to retain unused or undriven inputs in an  
appropriate state. The recommended pull-up value of 3kΩ to +3.3V (10kΩ to +5V can be used on 5V tolerant I/Os)  
and pull-down value of 1kΩ to GND, applies only to individually terminated signals. To prevent possible damage to  
the device, I/Os capable of becoming outputs must never be tied together and terminated through a common  
resistor.  
If your system-level test methodology permits, input-only signals can be connected together and terminated  
through either a common resistor or directly to +3.3V or GND. When a resistor is used, its value must ensure that  
the grouped I/Os reach a valid logic zero or logic one state when accounting for the total input current into the  
PPC405GPr.  
Unused I/Os  
For some interfaces, it is possible to turn off input receivers for some or all of the signals by means of bit settings in  
register CPC0_CR1. When this gating capability is applied to unused signals, it is not necessary to terminate them.  
Refer to the PowerPC 405GPr Embedded Processor User’s Manual for details.  
If receiver gating is not used, termination of some pins may be necessary when they are unused. Although the  
PPC405GPr requires only the pull-up and pull-down terminations as specified in the “Signal Functional  
Description” on page 30, good design practice is to terminate all unused inputs or to configure I/Os such that they  
always drive. If unused, and receiver gating is not used, the peripheral, SDRAM, and PCI buses should be  
configured and terminated as follows:  
• Peripheral interface—PerAddr0:31, PerData0:31, and all of the control signals are driven by default. Terminate  
PerReady high and PerError low.  
• SDRAM—Program SDRAM0_CFG[EMDULR]=1 and SDRAM0_CFG[DCE]=1. This causes the PPC405GPr to  
actively drive all of the SDRAM address, data, and control signals.  
• PCI—The PCI pull-up requirements given in the Signal Functional Description apply only when the PCI  
interface is being used. When the PCI bridge is unused, configure the PCI controller to park on the bus and  
actively drive PCIAD31:0, PCIC3:0[BE3:0], and the remaining PCI control signals by doing the following:  
- Strap the PPC405GPr to disable the internal PCI arbiter and to operate the PCI interface in synchronous  
mode.  
- Individually connect PCISErr, PCIPErr, PCITRDY, and PCIStop through 3kΩ resistors to +3.3V.  
- Terminate PCIReq1:5 to +3.3V.  
- Terminate PCIReq0[Gnt] to GND.  
External Bus Control Signals  
All peripheral bus control signals (PerCS0:7, PerR/W, PerWBE0:3, PerOE, PerWE, PerBLast, HoldAck, ExtAck)  
are set to the high-impedance state when ExtReset=0. In addition, as detailed in the PowerPC 405GPr Embedded  
Processor User’s Manual, the peripheral bus controller can be programmed via EBC0_CFG to float some of these  
control signals between transactions and/or when an external master owns the peripheral bus. As a result, a pull-  
up resistor should be added to those control signals where an undriven state may affect any devices receiving that  
particular signal.  
The following table lists all of the I/O signals provided by the PPC405GPr. Please refer to “Signals Listed  
Alphabetically” on page 16 for the pin number to which each signal is assigned.  
AMCC  
29  
 复制成功!