S P E C I F I C AT I O N S
JNIC-1460/1560
Features
All Models
• Switched Fabric, Arbitrated Loop, and
Point-to-Point topology support
• Multi-layer software architecture
JNIC-1460
• Integrated RISC-based I/O Engine
• 1 or 2 Gb Fibre Channel Data Rate
• 66MHz, 64-bit PCI 2.2 Compliant
• Hardware Assisted Context Switching
• Local Memory Port with Bursting Option
• Concurrent Target and Initiator
Mode Support
JNIC-1560
• Two fully independent Fibre Channel (FC)
ports on a single ASIC
• Integrated native PCI-X, 50 to 133MHz, 64-
bit host interface
• Automatic rate negotiation from
1 to 2Gb
• Multi-protocol capable
(FCP, IP, FC-Tape, FC-BB)
• 10- or 20-bit external SERDES support
Applications
JNIC-1460
• Mission critical SANs requiring simultaneous
high-speed transactions between multiple
Fibre Channel links and a single server
JNIC-1560
• High-end servers and high-performance
embedded storage applications.
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
JNIC-1460 Specifications
Host (PCI) Interface
66 MHz PCI clock rate
32- or 64-bit data path
Zero-wait state transfers with cache line streaming
Message Signal Interrupt (MSI) support
Independent DMA channels for receive, transmit
and command
Programmable priority for the DMA channels
64-bit addressing
Dual address cycle capable
Power management registers
PCI 2.2 and PC99 compliant
Fibre Channel Interface
1 or 2 Gb Full-Duplex FC data rate
Auto Link Speed Negotiation
Simultaneous Multi-protocol Capable
Up to 126 ALPA Aliases
Switched Fabric, Arbitrated Loop, and Point-to-Point
Support for class 1, 2, 3, and intermix services
Dynamic half-duplex support
10- or 20-bit external SERDES Interface
Raw frame handling
Programmable removal from loop
Loopback control, error status block, LRC control,
and busy indicator
FC-AL-2 rev. 7.0 compliant
Local Memory Interface
De-multiplexed address and data
Synchronous SRAM for local active exchanges
Direct connect 64K to 256K by 18 Sync. SRAM
Local nonvolatile memory (up to 1 MB)
SEEPROM (2 Kb) support
8 GPIO pins
Local interrupt input
JNIC-1560 Specifications
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Host (PCI) Interface
32/64-bit PCI up to 66 MHz
32/64-bit PCI-X 50 MHz to 133 MHz
Maximum PCI-X burst rate of 1064 MB
Maximum PCI burst rate of 528 MB
PCI-X Split Transaction support
Zero wait state PCI Bus Master transfers with cache
line streaming
Support for Message Signaled Interrupt
Independent PCI REQ/GNT pairs per port
Programmable parity
Dual address cycle capable
PCI 2.2 and PCI-X 1.0a compliant
Fibre Channel Interface
Two fully independent Fibre Channel ports
800 MB full-duplex FC data rate
2 Gb Fibre Channel with Auto Speed Detect
Switched fabric, point-to-point, arbitrated loop
Multi-Protocol Capable (FCP, IP, FC-BB)
Dedicated RISC Engine for each port
Dynamic half-duplex support
Supports 126 AL_PA aliasing
Link diagnostics, including loop back control,
error status block, LRC control and busy indicator
Raw frame transmit and receive mode
GBIC & MIA Support
FC-AL-2 rev. 7.0 compliant
Local Memory Interface
Synchronous SRAM for local command storage
8-Mb flash memory support (1 MB)
Parity protected data paths
8 general purpose I/O pins (4 per port)
Two local interrupt inputs
Optional 4K-bit Serial EEPROM interface
Software Support
• Multi-layer API
• Concurrent target & initiator mode support
• FCP, IP, FC-BB, and FC-Tape support
Physical Dimensions
• 388-pin PBGA
• 35mm by 35mm
• 1.27 mm pitch
Environmental
• Operating temperature: 0° to 70° C
• Storage Temperature: -40° to 85° C
• Relative humidity: 8% to 85% non-condensing
Reliability
• Internal and external loopback mode
• IEEE 1149.1 JTAG interface
• Parity protection on all data paths
E N TE RP RIS E
Software Support
• Multi-layer API
• Concurrent target & initiator mode support
• FCP, IP, FC-BB and FC-Tape support
Physical Dimensions
• 476-pin PBGA
• 35mm by 35mm
• 1.27 mm pitch
•
•
•
•
Environmental
Operating temperature: 0° to 70° C
Storage Temperature: -40° to 85° C
Relative humidity: 8% to 85% non-condensing
Maximum Power consumption: 2.5 Watts
Reliability
• Internal and external loopback modes
• IEEE 1149.1 JTAG interface
• Parity protection on all data paths
For technical support, please call 877-436-5642 or email support@amcc.com.
6290 Sequence Drive
San Diego, CA 92121
P 858 450 9333
F 858 450 9885
www.amcc.com
AMCC reserves the right to make changes to its products, or to discontinue any product or service without notice, and
advises its customers to obtain the latest version of relevant information to verify, before placing orders, that the informa-
tion being relied upon is current.
AMCC is a registered trademark of Applied Micro Circuits Corporation. All other trademarks are the property of their
respective holders. Copyright © 2004 Applied Micro Circuits Corporation. All Rights Reserved.
JNIC1460/1560_DS_09/01/2004
AMCC [ APPLIED MICRO CIRCUITS CORPORATION ]
