AS4C128M16D3A-12BIN
- Write Recovery
The programmed WR value MR0 (bits A9, A10, and A11) is used for the auto precharge feature along with tRP to
determine tDAL. WR (write recovery for auto-precharge) min in clock cycles is calculated by dividing tWR (ns) by
tCK (ns) and rounding up to the next integer: WR min [cycles] = Roundup (tWR [ns]/tCK [ns]). The WR must be
programmed to be equal or larger than tWR (min).
- Precharge PD DLL
MR0 (bit A12) is used to select the DLL usage during precharge power-down mode. When MR0 (A12=0), or ‘slow-
exit’, the DLL is frozen after entering precharge power-down (for potential power savings) and upon exit requires
tXPDLL to be met prior to the next valid command. When MR0 (A12=1), or ‘fast-exit’, the DLL is maintained after
entering precharge power-down and upon exiting power-down requires tXP to be met prior to the next valid
command.
z Mode Register MR1
The Mode Register MR1 stores the data for enabling or disabling the DLL, output strength, Rtt_Nom impedance,
additive latency, WRITE leveling enable and Qoff. The Mode Register 1 is written by asserting low on CS#, RAS#,
CAS#, WE#, high on BA0 and low on BA1 and BA2, while controlling the states of address pins according to the
following figure.
Table 7. Extended Mode Register EMR (1) Bitmap
BA2 BA1 BA0 A13 A12 A11 A10 A9
A8
A7
A6
A5
A4
A3
A2
A1
A0 Address Field
0*1
0*1 0*1
0*1
0*1
0
1
Qoff
AL
DLL Mode Register (1)
Rtt_Nom
Rtt_Nom
Rtt_Nom
Level
D.I.C
D.I.C
DLL Enable
Enable
BA1 BA0 MRS mode
A4 A3
Additive Latency
0 (AL disabled)
CL – 1
A0
0
0
0
1
0
1
0
MR0
MR1
MR2
0
0
1
0
1
0
Disable
1
CL – 2
1
1
MR3
1
1
Reserved
A12
Qoff *2
A9 A6 A2
Rtt_Nom *3
0
1
Output buffer enabled
Output buffer disabled
0
0
0
0
1
1
1
1
0
0
1
1
0
0
1
1
0
1
0
1
0
1
0
1
Rtt_Nom disabled
RZQ/4
Write leveling enable
Disabled
A7
0
RZQ/2
RZQ/6
1
Enabled
RZQ/12 *4
RZQ/8 *4
Reserved
Reserved
Note: RZQ = 240 Ω
Output Driver Impedance Control
A5
0
A1
0
RZQ/6
RZQ/7
Note: RZQ = 240 Ω
0
1
1
0
Reserved
Reserved
1
1
Note 1: Reserved for future use and must be set to 0 when programming the MR.
Note 2: Outputs disabled - DQs, DQSs, DQS#s.
Note 3: In Write leveling Mode (MR1 [bit7] = 1) with MR1 [bit12] =1, all RTT_Nom settings are allowed; in Write Leveling
Mode (MR1 [bit7] = 1) with MR1 [bit12]=0, only RTT_Nom settings of RZQ/2, RZQ/4 and RZQ/6 are allowed.
Note 4: If RTT_Nom is used during Writes, only the values RZQ/2, RZQ/4 and RZQ/6 are allowed.
Confidential
-16/83-
Rev. 1.0 May 2016