欢迎访问ic37.com |
会员登录 免费注册
发布采购

AS29F200B-120SI 参数 Datasheet PDF下载

AS29F200B-120SI图片预览
型号: AS29F200B-120SI
PDF下载: 下载PDF文件 查看货源
内容描述: 5V 256K ×8 / 128K ×8 CMOS FLASH EEPROM [5V 256K x 8/128K x 8 CMOS FLASH EEPROM]
分类和应用: 可编程只读存储器电动程控只读存储器电可擦编程只读存储器
文件页数/大小: 20 页 / 357 K
品牌: ALSC [ ALLIANCE SEMICONDUCTOR CORPORATION ]
 浏览型号AS29F200B-120SI的Datasheet PDF文件第4页浏览型号AS29F200B-120SI的Datasheet PDF文件第5页浏览型号AS29F200B-120SI的Datasheet PDF文件第6页浏览型号AS29F200B-120SI的Datasheet PDF文件第7页浏览型号AS29F200B-120SI的Datasheet PDF文件第9页浏览型号AS29F200B-120SI的Datasheet PDF文件第10页浏览型号AS29F200B-120SI的Datasheet PDF文件第11页浏览型号AS29F200B-120SI的Datasheet PDF文件第12页  
$65<)533  
                                           
                                           
                                           
                                           
                                            
                                            
                                            
                                            
                                             
                                             
                                             
                                             
                                              
                                              
                                              
                                              
                                               
                                               
                                               
                                               
                                                
                                                
                                                                                                                                          
                                                                                                                                          
                                                 
                                                 
                                                 
                                                 
                                                  
                                                  
                                                  
                                                  
                                                   
                                                   
                                                   
                                                   
                                                    
                                                    
                                                     
                                                     
                                                     
                                                     
                                                     
                                                     
                                                      
                                                      
3UHOLPLQDU\#LQIRUPDWLRQ  
®
Checks whether sector erase timer window is open. If DQ3 = 1, erase is in progress; no commands  
will be accepted. If DQ3 = 0, the device will accept sector erase commands. Check DQ3 before and  
after each sector erase command to verify that the command was accepted.  
Sector erase timer  
(DQ3)  
During sector erase, DQ2 toggles with OE or CE only during an attempt to read a sector being  
erased. During chip erase, DQ2 toggles with OE or CE for all addresses. If DQ5 = 1, DQ2 toggles  
only at sector addresses where failure occurred, and will not toggle at other sector addresses. Use  
DQ2 in conjunction with DQ6 to determine whether device is in auto erase or erase suspend  
mode.  
Toggle bit 2 (DQ2)  
&RPPDQG#IRUPDW  
2nd bus  
3rd bus  
4th bus  
5th bus  
6th bus  
1st bus write cycle  
write cycle  
write cycle  
read/ write cycle  
write cycle  
write cycle  
Required  
Command sequence bus cycles Address Data Address Data Address Data Address  
Data Address Data Address Data  
Read  
Reset/ Read  
1
XXXXh  
F0h  
Read Data  
Address  
2AAAh  
5555h  
×16  
×8  
5555h  
AAAAh  
5555h  
AAAAh  
Read  
Address  
Read  
Data  
Reset/ Read  
4
AAh  
55h  
F0h  
90h  
2251h(T)  
2257h (B)  
×16  
5555h  
AAAAh  
2AAAh  
5555h  
5555h  
AAAAh  
01h  
02h  
51h (T)  
57h (B)  
×8  
Autoselect  
ID Read  
4
AAh  
55h  
00h  
MFR code  
×16/ ×8  
52h  
×16  
×8  
XXX02h  
XXX04h  
01 = protected  
00 = unprotected  
×16  
×8  
5555h  
AAAAh  
5555h  
AAAAh  
5555h  
AAAAh  
XXXXh  
XXXXh  
2AAAh  
5555h  
2AAAh  
5555h  
2AAAh  
5555h  
5555h  
AAAAh  
5555h  
AAAAh  
5555h  
AAAAh  
Program  
Address  
Program  
Data  
Program  
4
6
6
AAh  
AAh  
AAh  
55h  
55h  
55h  
A0h  
80h  
80h  
×16  
×8  
5555h  
AAAAh  
5555h  
AAAAh  
2AAAh  
5555h  
AAAAh  
Chip Erase  
Sector Erase  
AAh  
AAh  
55h  
55h  
10h  
30h  
5555h  
2AAAh  
5555h  
×16  
×8  
Sector  
Address  
Sector Erase Suspend  
Sector Erase Resume  
1
1
B0h  
30h  
1
2
3
4
5
6
Bus operations defined in "Mode definitions," on page 4.  
Reading data from or programming data to non-erasing sectors allowed in Erase Suspend mode.  
Address bit A15 = X = Don’t care for all address commands except Program Address and Sector Address.  
Address bit A16 = X = Don’t care for all address commands except Program Address and Sector Address.  
System should generate address patterns: ×16 mode - 5555h or 2AAAh to address A0A14; ×8 mode - AAAAh or 5555h to address A-1A14.  
A = 0, A = 1, A = 0 for sector protect verify; sector selected on A16-A12.  
0
1
6
;
$//,$1&(#6(0,&21'8&725  
','#4407333<0$1#72:233