欢迎访问ic37.com |
会员登录 免费注册
发布采购

A1141EUATI 参数 Datasheet PDF下载

A1141EUATI图片预览
型号: A1141EUATI
PDF下载: 下载PDF文件 查看货源
内容描述: [Analog Circuit, 1 Func, BICMOS, PSIP3, ULTRA MINI, SIP-3]
分类和应用: 开关
文件页数/大小: 13 页 / 344 K
品牌: ALLEGRO [ ALLEGRO MICROSYSTEMS ]
 浏览型号A1141EUATI的Datasheet PDF文件第1页浏览型号A1141EUATI的Datasheet PDF文件第2页浏览型号A1141EUATI的Datasheet PDF文件第3页浏览型号A1141EUATI的Datasheet PDF文件第5页浏览型号A1141EUATI的Datasheet PDF文件第6页浏览型号A1141EUATI的Datasheet PDF文件第7页浏览型号A1141EUATI的Datasheet PDF文件第8页浏览型号A1141EUATI的Datasheet PDF文件第9页  
Sensitive Two-Wire Chopper-Stabilized  
Unipolar Hall Effect Switches  
A1140, A1141,  
A1142, and A1143  
ELECTRICAL CHARACTERISTICS over the operating voltage and temperature ranges, unless otherwise specified  
Characteristic  
Supply Voltage1  
Symbol  
Test Conditions  
Min.  
3.5  
2
Typ.  
Max.  
24  
Units  
V
VCC  
B>BOP for A1140; B<BRP for A1141  
B>BOP for A1142; B<BRP for A1143  
5
mA  
mA  
ICC(L)  
5
-–  
6.9  
Supply Current2  
B>BOP for A1141, A1143  
B<BRP for A1140, A1142  
ICC(H)  
IRCC  
12  
-–  
17  
mA  
Reverse Supply Current  
VRCC = –18 V  
28  
–1.6  
40  
mA  
V
Supply Zener Clamp Voltage VZSUPPLY ICC = ICC(L)(max) + 3 mA; TA = 25°C  
ICC(L)(max)  
+ 3 mA  
Supply Zener Clamp Current  
Output Slew Rate3  
IZSUPPLY VZSUPPLY = 28 V  
mA  
Capacitance of the oscilloscope performing the  
measurement = 20 pF  
di/dt  
36  
mA/μs  
Chopping Frequency  
Power-On Time3  
fC  
ton  
200  
25  
kHz  
s  
CBYPASS = 0.01 μF  
Power-On State5,6  
POS  
t < ton; VCC slew rate > 25 mV/s  
HIGH  
1VCC represents the generated voltage between the VCC pin and the GND pin.  
2Relative values of B use the algebraic convention, where positive values indicate south magnetic polarity, and negative values indicate north magnetic  
polarity; therefore greater B values indicate a stronger south polarity field (or a weaker north polarity field, if present).  
3Measured without bypass capacitor between VCC and GND. Use of a bypass capacitor results in slower current change.  
3Measured with and without bypass capacitor of 0.01 μF. Adding a larger bypass capacitor causes longer Power-On Time.  
5POS is defined as true only with a VCC slew rate of 25 mV/μs or greater. Operation with a VCC slew rate less than 25 mV/μs can permanently harm  
device performance.  
6POS is undefined for t > ton or BRP < B < BOP  
.
MAGNETIC CHARACTERISTICS over the operating voltage and temperature ranges, unless otherwise specified  
Characteristic  
Symbol  
Test Conditions  
Min.  
Typ.*  
Max.  
Units  
A1140, A1142 ICC = ICC(L)  
Operate Point  
BOP  
50  
80  
110  
G
A1141, A1143  
A1140, A1142 ICC = ICC(H)  
A1141, A1143 CC = ICC(L)  
BHYS = BOP – BRP  
ICC = ICC(H)  
Release Point  
Hysteresis  
BRP  
45  
5
65  
15  
105  
30  
G
G
I
BHYS  
*Typical data are for initial design estimations only, and assume optimum manufacturing and application conditions, such as TA = 25°C and VCC = 12 V.  
Performance may vary for individual units, within the specified maximum and minimum limits.  
Allegro MicroSystems, Inc.  
115 Northeast Cutoff, Box 15036  
4
Worcester, Massachusetts 01615-0036 (508) 853-5000  
www.allegromicro.com