欢迎访问ic37.com |
会员登录 免费注册
发布采购

AK4184VG 参数 Datasheet PDF下载

AK4184VG图片预览
型号: AK4184VG
PDF下载: 下载PDF文件 查看货源
内容描述: TSC与键盘扫描和GPIO扩展器 [TSC with Keypad Scanner and GPIO Expander]
分类和应用: 转换器模数转换器
文件页数/大小: 36 页 / 600 K
品牌: AKM [ ASAHI KASEI MICROSYSTEMS ]
 浏览型号AK4184VG的Datasheet PDF文件第8页浏览型号AK4184VG的Datasheet PDF文件第9页浏览型号AK4184VG的Datasheet PDF文件第10页浏览型号AK4184VG的Datasheet PDF文件第11页浏览型号AK4184VG的Datasheet PDF文件第13页浏览型号AK4184VG的Datasheet PDF文件第14页浏览型号AK4184VG的Datasheet PDF文件第15页浏览型号AK4184VG的Datasheet PDF文件第16页  
[AK4184]  
Keypad Scanner  
The AK4184 keypad scanner is designed to interface to a matrix type keypad with 5 rows x 6 columns (30keys or  
fewer) to the host controller. The KPMASK1, 2 and KPColumnMask register enable the masking of certain keys or a  
whole column of the keypad when any keys less than 30 keys or any columns less than 6 columns are not utilized.  
Keypad Interrupt Detection  
When the AK4184 is in key interrupt enabled mode, C1~C6 pins are designed to output “H” and R1~R5 pins are  
designed to pull to GND via Rkey (Rkey=16kΩ typ, Figure 5). When a key is pressed a related R1~R5 pin goes “H”  
and the KEYIRQN pin goes “L”. The KEYIRQN pin returns “H” after key press scan is completed. KEYIRQN pin  
does not go “L” again until the host reads the keypad read register (KPDATA1 or KPDATA2).  
Keypad Scan Data Read  
The AK4184 starts to scan the key condition in sequence and writes each keypad state to the registers after a key-  
press is detected. First the C1 pin goes to “H” (Scan Output1) and the C2 ~ C6 pins are in Hi-Z state. Certain Ry pins  
are connected to C1 and pulled “H”. The Ry pin returns “L” after the key-press is released. The AK4184 reads the Ry  
pin level (Sense Input 1 through 5) and loads the keypad data into the register. When two keys are pressed  
simultaneously, the associated row pins go “H” at the same time. Then the AK4184 C2 pin goes to “H” (Scan  
Output2), and reads and loads the R1 ~ R5 pin levels into the register (Sense Input 1 through 5). The same sequence  
as Scan Output 1 repeats up to Scan Output 6. The AK4184 makes this Scan Output and Sense Input pattern and loads  
the keypad-data into the register for unmasked columns.  
Debounce key scan performs a series of the Scan Output / Sense Input at the end of the debounce time interval, then  
the AK4184 loads the key pad data into the resister. μ-Processor starts to read the data register after confirming if the  
keypad scan completed. New keypad scan does not repeat again until the Host reads the keypad data.  
MS0603-E-00  
2007/04  
12