Switching Specifications
(T
A
= 25°C)
Parameter
Propagation Delay
Time to High Output
Level
Propagation Delay Time
to Low Output Level
Rise Time
Fall Time
Output High Level
Common Mode
Transient Immunity
Output Low Level
Common Mode
Transient Immunity
Sym.
t
PLH
Min.
-
Typ.
2
Max.
5
Units
µs
Test Conditions
V
CC
= 6 V, I
F
= 5 mA,
R
L1
= 5
Ω,
R
L2
= 10
Ω
Fig.
7,
24,
25
Note
2, 6
t
PHL
t
r
t
f
-
-
-
2
0.2
0.1
-
5
1
1
-
V/µs
V
CM
= 600 V
Peak
,
I
F
= 5mA, R
L1
= 470
Ω,
R
L2
= 1 kΩ,
∆V
02H
= 0.5 V
V
CM
= 600 V
Peak
,
I
F
= 0 mA, R
L1
= 470
Ω,
R
L2
= 1 kΩ,
∆V
02L
= 0.5 V
8
2
|CM
H
| 1500
|CM
L
| 1500
-
-
V/µs
Package Characteristics
Parameter
Sym. Min. Typ.
Input-Output Momentary V
ISO
5000
Withstand Voltage*
Resistance
R
I-O
5x10
10
10
11
(Input-Output)
Capacitance
C
I-O
–
1.2
(Input-Output)
Max.
Units
V rms
Ω
pF
Test Conditions
RH = 40% to 60%,
t = 1 min., T
A
= 25°C
V
I-O
= 500 V, T
A
= 25°C,
RH = 40% to 60%
f = 1 MHz
Fig.
Note
4, 5
4
4
–
–
*The Input-Output Momentary Withstand Voltage is a dielectric voltage rating that should not be interpreted as an input-output
continuous voltage rating. For the continuous voltage rating refer to the VDE 0884 Insulation Characteristics Table (if applicable), your
equipment level safety specification, or HP Application Note 1074, “Optocoupler Input-Output Endurance Voltage.”
Notes:
1. Derate absolute maximum ratings with ambient temperatures as shown in Figures 9, 10, and 11.
2. A bypass capacitor of 0.01
µF
or more is needed near the device between V
CC
and GND when measuring output and transfer
characteristics.
3. I
FLH
represents the forward current when the output goes from low to high.
4. Device considered a two terminal device; pins 1-4 are shorted together and pin 5-8 are shorted together.
5. For devices with minimum V
ISO
specified at 5000 V rms, in accordance with UL1577, each optocoupler is proof-tested by applying an
insulation test voltage
≥
6000 V rms for one second (leakage current detection limit, I
I-O
≤
200
µA).
6. The t
PLH
and t
PHL
propagation delays are measured from the 50% level of the input pulse to the 50% level of the output pulse.
7. R
1
sets the base current (I
O1
in Figure 1) supplied to the power bipolar device. R
2
limits the peak current seen by Q2 when the device
is turning off. For more applications and circuit design information see Application Note “Power Transistor Gate/Base Drive
Optocouplers.”
1-333
AGILENT [ AGILENT TECHNOLOGIES, LTD. ]
